Related papers: A Schottky-Diode-Based Wake-Up Receiver for IoT Ap…
This paper studies the massive machine-type communications (mMTC) for the future Internet of Things (IoT) applications, where a large number of IoT devices exist in the network and a random subset of them become active at each time instant.…
Simultaneous wireless information and power transfer (SWIPT) has emerged as a viable technique to energize and connect low-power autonomous devices and enable future Internet of Things (IoT). A major challenge of SWIPT is the energy…
With the advancements in underwater wireless communications, internet of underwater things (IoUT) realization is inevitable to enable many practical applications, such as exploring ocean resources, ocean monitoring, underwater navigation,…
The low-power radio technologies open up many opportunities to facilitate Internet-of-Things (IoT) into our daily life, while their minimalist design also makes IoT devices vulnerable to many active attacks. Recent advances use an antenna…
A low noise and wide dynamic range event driven detector for the detection of X-Ray energy is realized using 0.2 [um] Silicon on insulator (SOI) technology. Pixel circuits are divided into two parts; signal sensing circuit and event…
In this paper, a sub-uW power 802.11b backscattering transmitter is presented to enable reuse of the same incident wave for three purposes: RF harvesting, backscattering communications and position/motion sensing. The removal of the battery…
Demand for on-chip low-dropout regulators (LDOs) with both high power-supply rejection ratio (PSRR) and fast transient response is growing as system-on-chip (SoC) integration increases. However, conventional LDO architectures face…
Low-power wide-area network technologies such as LoRaWAN are promising for collecting low-rate monitoring data from geographically distributed sensors, in which timestamping the sensor data is a critical system function. This paper…
Effective wireless communications are increasingly important in maintaining the successful closed-loop operation of mission-critical industrial Internet-of-Things (IIoT) applications. To meet the ever-increasing demands on better wireless…
Voltage doubler rectifiers are usually applied to systems with high voltage and low current requirement. An X band voltage doubler rectifier has been developed with 72% conversion efficiency. To the best of our knowledge, the obtained…
A well-balanced detector with high sensitivity and low noise is presented in this paper. The two-stage amplification structure is used to increase electronic gain while keeping an effective bandwidth of about 70 MHz. In order to further…
Minimizing the energy consumption of Linux-based devices is an essential step towards their wide deployment in various IoT scenarios. Energy saving methods such as duty-cycling aim to address this constraint by limiting the amount of time…
Wireless-powered communications (WPCs) are increasingly crucial for extending the lifespan of low-power Internet of Things (IoT) devices. Furthermore, reconfigurable intelligent surfaces (RISs) can create favorable electromagnetic…
We investigate the activity detection and channel estimation issues for cell-free Internet of Things (IoT) networks with massive random access. In each time slot, only partial devices are active and communicate with neighboring access…
Certain sensing applications such as Internet of Things (IoTs), where the sensing phenomenon may change rapidly in both time and space, requires sensors that consume ultra-low power (so that they do not need to be put to sleep leading to…
Low-power and cost-effective IoT sensing nodes enable scalable monitoring of different environments. Some of these environments impose rough and extreme operating conditions, requiring continuous adaptation and reconfiguration of physical…
This article addresses an innovative concept to enhance the security for IoT applications in the case of Simultaneous Wireless Information and Power Transfer. This is achieved by integrating a complementary security and identification…
Room temperature microwave and low-THz links exhibit large thermal occupations, making phase sensitive signal-idler correlations difficult to recover after loss. We introduce a work-extraction-based quantum-illumination receiver in which…
Discontinuous reception (DRX), where a user equip-ment (UE) temporarily disables its receiver, is a critical power saving feature in modern cellular systems. DRX is likely tobe particularly aggressively used in the mmWave and THzfrequencies…
A new prototype wireless data acquisition system has been developed with the intended application to read-out instrumentation systems having a large number of channels. In addition such system could be deployed in smaller detectors…