Related papers: Arc plasma ablation of quartz crystals
A switching-off process very similar to those in real high-voltage self-blast circuit-breakers is emulated in a model chamber to study the arc properties by optical emission spectroscopy. The arc is operated in a chamber filled with SF$_6$…
In the atmospheric pressure anodic carbon arc, ablation of the anode serves as a feedstock of carbon for production of nanomaterials. It is known that the ablation of the graphite anode in this arc can have two distinctive modes with low…
In this paper, we present the laboratory study on three experimental setups that produce a free arc channel subjected to the transient phase of a lightning current waveform. This work extends the high-current pulsed arc characterization…
Short atmospheric pressure argon arc is studied numerically and analytically. In a short arc with inter-electrode gap of several millimeters non-equilibrium effects in plasma play important role in operation of the arc. High anode…
We investigate ablation experiments performed by laser-plasma-filament guided electrical discharges at high-voltages of up to 145 kV. The guiding was accomplished via fs-laser-generated plasma filaments across a gap of 201 mm of air onto…
Atmospheric pressure steam/oxygen plasma is generated by a 88 Hz, 6kV AC power supply. The properties of the produced plasma are investigated by optical emission spectroscopy (OES). The relative intensity, rotational, vibrational,…
Ultrafast laser heating of electrons on a metal surface breaks the pressure equilibrium within the material, thus initiating ablation. The stasis of a room-temperature metal results from a balance between repulsive and attractive binding…
Ablation of Cu and Al targets has been performed with 170 fs laser pulses in the intensity range of 10^12-10^14 W/cm^2. We compare the measured removal depth with 1D hydrodynamic simulations. The electron-ion temperature decoupling is taken…
Laser-induced water ablation triggers various physical effects, including atom ionization, optical breakdown of the liquid, phase explosion, cavitation, and shockwave propagation. These effects can be further amplified in heavy water by…
Spectroscopic characterization of a specific case of the atmospheric pressure air jet plasma in the transverse cw dc arc discharge of high voltage was done. Within the spectrum of wavelengths from 200 to 1100 nm all remarkable emissions…
Microwave plasmas are a promising technology for energy-efficient CO$_{2}$ valorization via conversion of CO$_{2}$ into CO and O$_2$ using renewable energies. A 2.45 GHz microwave plasma torch with swirling CO$_{2}$ gas flow is studied in a…
Time integrated spectroscopic measurements are carried out to characterize transient plasma stream produced in a coaxial pulsed plasma accelerator. This method allows the estimation of different plasma parameters and its evolution with…
We characterize the plasma flows generated during the ablation stage of an over-massed exploding planar wire array, fielded on the COBRA pulsed-power facility (1 MA peak current, 250 ns rise time). The planar wire array is designed to…
We provide measurements of ablation of four post-transition and transition metals (aluminum, copper, nickel and tungsten) irradiated by single 800 nm laser pulses, in ultrashort regime from 100 fs pulse duration down to 15 fs covering a…
The mechanism of ablation of solids by intense femtosecond laser pulses is described in an explicit analytical form. It is shown that at high intensities when the ionization of the target material is complete before the end of the pulse,…
We design and fabricate large-area (1.1 mm $\times$ 1.1 mm) photonic crystal quantum cascade lasers, enabling single-mode (wavelength $\sim$ 8.5 $\mu$m) surface emission at room temperature, with a maximum peak power up to 176 mW. The beam…
We demonstrate loading by laser ablation of $^{88}$Sr$^+$ ions into a mm-scale surface-electrode ion trap. The laser used for ablation is a pulsed, frequency-tripled Nd:YAG with pulse energies of 1-10 mJ and durations of 3-5 ns. An…
We present the development, manufacturing and performance of spherically bent crystal analyzers (SBCAs) of 100 mm diameter and 0.5 m bending radius. The elastic strain in the crystal wafer is partially released by a "strip-bent" method…
Graphite ablation in a presence of inert background gas is widely used in different methods for the synthesis of carbon nanotubes, including electric arc and laser/solar ablation. The ablation rate is an important characteristic of the…
A new parameterized model for the ablation phenomena is presented. The model describes the three different regimes usually observed, as a function of the laser fluence. The first one corresponds to a vaporization; it takes place at low…