Related papers: Design guidelines for a highly efficient high-puri…
This paper proposes an efficient three-layered p-GaAs/p-CIGS/n-CdS (PPN), a unique solar cell architecture. Copper indium gallium selenide (CIGS)-based solar cells exhibit substantial performance than the ones utilizing cadmium sulfide…
Ternary chalcostibite copper antimony selenide (CuSbSe2) is a promising absorber material for next generation thin film solar cells due to the non-toxic nature, earth-abundance, low-cost fabrication technique, optimum bandgap and high…
Inorganic CdTe and FeSi2-based solar cells have recently drawn a lot of attention because they offer superior thermal stability and good optoelectronic properties compared to conventional solar cells. In this work, a unique alternative…
In this article, we demonstrate CdSe-CuSbSe2-based double junction two-terminal tandem solar cells simulated with SCAPS-1D. The highest performance of the tandem cell has been confirmed by optimizing the electrical and optical properties of…
Solar cells manufactured on top of Ge substrates suffer from inherent drawbacks that hinder or limit their potential. The most deleterious ones are heavy weight, high bulk recombination, lack of photon confinement and an increase of the…
In this article, we demonstrate the design and simulation of a highly-efficient n-CdS/p-CIGS/p+-CGS dual heterojunction solar cell. The simulation was performed using SCAPS-1D software with reported experimental physical parameters. The…
By means of the first-principles density functional theory (DFT), I2-II-IV-VI4 type Cu-based quaternary chalcogenides Cu 2 XSiS 4 (X = Ge, Sn, and Pb) have been thoroughly investigated. We report the study of Ge and Sn substitution in the…
We report the first empirical efficiency measurement of germanium-based thermophotovoltaic devices under high-temperature, high-irradiance conditions using a high view-factor calorimetric setup. Two TPV cell architectures were fabricated on…
The p-type amorphous/ n-type crystalline silicon (P+ a-Si/N+ c-Si) heterojunction was simulated for developing the solar cells with high conversion efficiency and low cost. The characteristic of such cells with different work function of…
We simulated photovoltaic characteristics of single heterojunction solar cell with Cu2ZnSnS4 and Cu2ZnSnSe4 absorber layer numerically using one dimensional solar cell capacitance simulator (SCAPS-1D). n-CdS/ZnO double buffer layer is used…
Photovoltaic solar cell is one of the main renewable energy sources, and its power conversion efficiency (PCE) is improved by employing doping or heterojunction to reduce the photogenerated carrier recombination. Here, we propose a…
Multijunction solar cells are usually grown on Ge substrates. This implies several disadvantages that hinder the performance of the whole multijunction and limit their possible applications. The drawbacks caused by the substrate are:…
A high theoretical efficiency of 47.2% was achieved by a novel combination of In0.51Ga0.49P, GaAs, In0.24Ga0.76As and In0.19Ga0.81Sb subcell layers in a simulated quadruple junction solar cell under 1 sun concentration. The electronic…
Solar modules are currently characterized at standard test conditions (STC), defined at 1000W/m2 and 25 {\deg}C. However, solar modules in actual outdoor operating conditions typically operate at lower illumination and higher temperature…
Modern photovoltaic devices are often based on a heterojunction structure where two components with different optoelectronic properties are interfaced. The properties of each side of the junction can be tuned by either utilizing different…
In single-junction photovoltaic (PV) devices, the maximum achievable power conversion efficiency (PCE) is mainly limited by thermalization and transmission losses, because polychromatic solar irradiation cannot be matched to a single…
Virtual substrates based on thin Ge layers on Si by direct deposition have achieved high quality recently. Their application to high efficiency III-V solar cells is analyzed in this work. Replacing traditional Ge substrates with Ge/Si…
The electronic and optical properties of CdGa2Te4 and ZnGa2Te4 were studied using first-principles DFT calculations. Band gaps were calculated using the GGA-PBESol functional. Both materials show promise for photovoltaic applications…
Practical device architectures are proposed here for the implementation of three-terminal heterojunction bipolar transistor solar cells (3T-HBTSCs). These photovoltaic devices, which have a potential efficiency similar to that of…
Despite the promising optoelectronic properties of methylammonium lead iodide (MAPbI3)-based perovskite solar cells (PSCs), their commercial viability is hindered by interfacial energy misalignment, suboptimal light absorption, and thermal…