Related papers: Microstructural Changes Influencing the Magnetores…
Severe plastic deformation using high-pressure torsion of ternary Cu-based materials (CuFeCo and CuFeNi) was used to fabricate bulk samples with a nanocrystalline microstructure. The goal was to produce materials featuring the granular…
Bulk metallic samples were synthesized from different binary powder mixtures consisting of elemental Cu, Co, and Fe using severe plastic deformation. Small particles of the ferromagnetic phase originate in the conductive Cu phase, either by…
In this study, severe plastic deformation by high pressure torsion is used as a fabrication method for nanocrystalline magnetic CuCo alloys in bulk quantities. By subsequent isothermal annealing, phase separation of the supersaturated solid…
Nanocrystalline materials are well known for their beneficial mechanical and physical properties. However, it is of utmost importance to stabilize the microstructure at elevated temperatures to broaden the window of application e.g. by…
This work gives insights into processing and characterisation of bulk nanocrystalline FeCr materials. The investigated FeCr alloys, consisting of 30, 50 and 70 at.% ferromagnetic Fe and remaining anti-ferromagnetic Cr, are processed by arc…
We prepared very high-coercivity cobalt ferrite nanoparticles using short-time high-energy mechanical milling. After the milling process, the coercivity of the nanoparticles reached 3.75 kOe - a value almost five times higher than that…
In this study, a preparation route of Co-Cu alloys with soft magnetic properties by high-pressure torsion deformation is introduced. Nanocrystalline, supersaturated single-phase microstructures are obtained after deformation of Co-Cu…
The structure and magnetic properties of nanocrystalline PrCo$_3$ obtained from high energy milling technique are investigated by X-ray diffraction, Curie temperature determination and magnetic properties measurements are reported. The…
The periodic response of magnetoresistance to an externally tunable parameter, such as magnetic field or chemical composition, in the bulk or an artificially designed material has been exploited for technological applications as well as to…
The magnetic behavior of $Fe_{3-x}O_4$ nanoparticles synthesized either by high-temperature decomposition of an organic iron precursor or low-temperature co-precipitation in aqueous conditions, is compared. Transmission electron microscopy,…
A series of Co_xCu_{100-x} (x = 0, 40...75, 100) layers with thicknesses in-between 13 nm and 55 nm were prepared on silicon substrates using cross-beam pulsed laser deposition. Wide-angle X-ray diffraction (WAXRD), transmission electron…
Mixtures of Fe and Cu powders are cold-compacted and subsequently deformed with severe plastic deformation by high-pressure torsion, leading to bulk samples. The dilution of Fe in the Cu matrix is investigated with SQUID-magnetometry,…
Severe plastic deformation of powder blends consisting of SmCo5-Cu results in magnetically hardened nanocomposite bulk materials. The microstructure is continuously refined with increasing torsional deformation, yet, coercivity saturates at…
Initial powder mixtures of Cu, Fe and Co are exposed to severe plastic deformation by high-pressure torsion to prepare solid solutions. A broad range of compositions is investigated, whereas this study aims at the synthesis of soft magnetic…
The structure and magnetic properties of nanocrystalline PrCo$_3$ prepared by high-energy milling technique have been investigated by means of X-ray diffraction using the Rietveld method coupled to Curie temperature and magnetic…
The thermal decomposition behavior, the microstructural evolution and its influence on the mechanical properties of a supersaturated Cu Co solid solution with ~100 nm average grain size prepared by severe plastic deformation is investigated…
Understanding nanomechanical response of materials represents a scientific challenge. Here, we have used in-situ electron microscopy to reveal drastic for the first time changes of structural behavior during deformation of 1-nm-wide metal…
Processing magnetocaloric materials into magnetic refrigerants with appropriate shapes is essential for the development of magnetic refrigeration systems. In this context, the impact of processing on the physical properties of…
Co2FeAl (CFA) nanoparticles (NPs) of different sizes were synthesized by chemical route. The effect of the size of NPs upon the structure and magnetization compared to its bulk counterpart was investigated. The structure and composition…
We have measured the magnetoresistance of stretched sheets of carbon nanotubes in temperatures ranging from 2 K to 300 K and in magnetic fields up to 9 T, oriented either perpendicular or parallel to the plane of the sheets. The samples…