Related papers: Tailoring Interdigitated Back Contacts for High-pe…
A high theoretical efficiency of 47.2% was achieved by a novel combination of In0.51Ga0.49P, GaAs, In0.24Ga0.76As and In0.19Ga0.81Sb subcell layers in a simulated quadruple junction solar cell under 1 sun concentration. The electronic…
In this paper we carried out theoretical study of the general issues related to the efficiency of SiC:H/a-Si:H single- and multi-junction tandem solar cells. Implementation of numerical simulations by the use of AMPS-1D program of…
The demand for high-efficiency photovoltaic systems necessitates innovations that transcend the efficiency limitations of single-junction solar cells. This study investigates a tandem photovoltaic architecture comprising a top-cell with a…
Bifacial tandem cells promise to reduce three fundamental losses (above-bandgap, below bandgap, and the uncollected light between panels) inherent in classical single junction PV systems. The successive filtering of light through the…
Independent current extraction in multi-junction solar cells has gained attention in recent years because it can deliver higher annual energy yield and can work for more semiconductor material combinations than the more established…
In single-junction photovoltaic (PV) devices, the maximum achievable power conversion efficiency (PCE) is mainly limited by thermalization and transmission losses, because polychromatic solar irradiation cannot be matched to a single…
Multi-junction solar cells provide a path to overcome the efficiency limits of standard silicon solar cells by harvesting more efficiently a broader range of the solar spectrum. However, Si-based multi-junction architectures are hindered by…
The 2D/3D construction of hybrid perovskite interfaces is gaining increasing attention due to their enhanced stability towards degradation without compromising the corresponding solar cell efficiency. Much of it is due to the interfacial…
To be able to increase the efficiency of perovskite solar cells which is one of the most substantial challenges ahead in photovoltaic industry, the structural and optical properties of perovskite CH3NH3PbI3-xBrx for values x=1-3 have been…
Ternary chalcostibite copper antimony selenide (CuSbSe2) is a promising absorber material for next generation thin film solar cells due to the non-toxic nature, earth-abundance, low-cost fabrication technique, optimum bandgap and high…
Analytic expressions for the $JV$-characteristics of three types of multi-junction configurations are derived. From these, expressions for the short circuit current, open circuit voltage and voltage at the maximum power point are found for…
Wide-gap Cu(In,Ga)S2 solar cells with In2O3:Sn (ITO) as transparent back contact are evaluated for the application as top cells in tandem devices. The effect of Na on the solar cell performance is investigated by supplying additional Na by…
The majority of photoelectrochemical (PEC) water splitting cells cannot drive the overall water splitting reactions without the assistance of an external power source. To provide added power, the cells are usually connected to photovoltaic…
Intermediate band solar cells (IBSCs) pursue the increase in efficiency by absorbing below-bandgap energy photons while preserving the output voltage. Experimental IBSCs based on quantum dots have already demonstrated that both…
To obtain significant increases in the Power Conversion Efficiency (PCE) of solar cells, future cell research and development should be based on the concomitant improvement of multiple material properties, rather than on the…
Organic-inorganic halide perovskite materials have emerged as attractive alternatives to conventional solar cell building blocks. Their high light absorption coefficients and long diffusion lengths suggest high power conversion efficiencies…
Tandem perovskite solar cells beckon as lower cost alternatives to conventional single junction solar cells, with all-perovskite tandem photovoltaic architectures showing power conversion efficiencies up to 26.4%. Solution-processing…
An indium arsenide photovoltaic cell with gold front contacts is designed for use in a near-field thermophotovoltaic (NF-TPV) device consisting of millimeter-size surfaces separated by a nanosize vacuum gap. The device operates with a doped…
CdTe is one of the leading materials for low cost, high efficiency thin-film solar cells, because it has a high absorption coefficient and a nearly ideal band gap of 1.48 eV for solar cell according to the Shockley-Queisser limit. However,…
Multi-junction photovoltaics provide a logical method of increasing the utilization of solar power for a given area. However, their current design and fabrication methods invoke numerous material and cost complexities that limit their…