Related papers: On Low-Resolution ADCs in Practical 5G Millimeter-…
The highly sparse nature of propagation channels and the restricted use of radio frequency (RF) chains at transceivers limit the performance of millimeter wave (mmWave) multiple-input multiple-output (MIMO) systems. Introducing…
Millimeter wave (mmWave) MIMO will likely use hybrid analog and digital precoding, which uses a small number of RF chains to avoid energy consumption associated with mixed signal components like analog-to-digital components not to mention…
The use of low-precision analog-to-digital converters (ADCs) is a low-cost and power-efficient solution for a millimeter wave (mmWave) multiple-input multiple-output (MIMO) system operating at sampling rates higher than a few Gsample/sec.…
Massive multiuser multiple-input multiple-output (MU-MIMO) systems are expected to be the core technology in fifth-generation wireless systems because they significantly improve spectral efficiency. However, the requirement for a large…
Spatial filtering based on multiple-input multiple-output (MIMO) processing is a powerful method for jammer mitigation. In principle, a MIMO receiver can null the interference of a single-antenna jammer at the cost of only one degree of…
As communication systems advance towards the future 6G era, the incorporation of large-scale antenna arrays in base stations (BSs) presents challenges such as increased hardware costs and energy consumption. To address these issues, the use…
Millimeter wave (mmWave) communication systems using adaptive-resolution analog-to-digital converters (RADCs) have recently drawn considerable interests from the research community as benefit of their high energy efficiency and low…
Millimeter wave (mmWave) band, or high frequencies such as THz, has large undeveloped band of spectrum. However, wireless channels over the mmWave band usually have one or two paths only due to the severe attenuation. The channel property…
In this paper, we present a new scenario of direction of arrival (DOA) estimation using massive multiple-input multiple-output (MIMO) receive array with low-resolution analog-to-digital convertors (ADCs), which can strike a good balance…
This letter considers the architecture of distributed antenna system, which is made up of a massive number of single-antenna remote radio heads (RRHs), some with full-resolution but others with low-resolution analog-to-digital converter…
Millimeter wave (mmWave) bands have been utilized for the fifth generation (5G) communication systems and will no doubt continue to be deployed for beyond 5G (B5G). However, the underlying channels are not fully investigated at…
Massive MIMO (Multiple Input Multiple Output) has demonstrated as a potential candidate for 5G-and-beyond wireless networks. Instead of using Gaussian signals as most of the previous works, this paper makes a novel contribution by…
We derive an expression for the capacity of massive multiple-input multiple-output Millimeter wave (mmWave) channel where the receiver is equipped with a variable-resolution Analog to Digital Converter (ADC) and a hybrid combiner. The…
With bandwidths on the order of a gigahertz in emerging wireless systems, high-resolution analog-to-digital convertors (ADCs) become a power consumption bottleneck. One solution is to employ low resolution one-bit ADCs. In this paper, we…
With the severe spectrum shortage in conventional cellular bands, millimeter-wave (mmWave) frequencies have been attracting growing attention for next-generation micro- and picocellular wireless networks. A fundamental and open question is…
The use of low-resolution analog-to-digital converters (ADCs) is considered to be an effective technique to reduce the power consumption and hardware complexity of wireless transceivers. However, in systems with low-resolution ADCs,…
Extremely low-resolution (e.g. one-bit) analog-to-digital converters (ADCs) and digital-to-analog converters (DACs) can substantially reduce hardware cost and power consumption for MIMO radar especially with large scale antennas. In this…
Millimeter-wave (mm-Wave) cellular systems are a promising option for a very high data rate communication because of the large bandwidth available at mm-Wave frequencies. Due to the large path-loss exponent in the mm-Wave range of the…
The deployment of millimeter wave (mmWave) multiple-input multiple-output (MIMO) systems cannot rely solely on digital precoding due to hardware constraints. Instead, hybrid precoding, which combines digital and radio frequency (RF)…
This paper investigates the hybrid precoding design for millimeter wave (mmWave) multiple-input multiple-output (MIMO) systems with finite-alphabet inputs. The mmWave MIMO system employs partially-connected hybrid precoding architecture…