Related papers: Three-dimensional printed Yttria-stabilized Zircon…
Inspired by the high critical temperature in yttrium superhydride and the low stabilized pressure in superconducting cerium superhydride, we carry out four independent runs to synthesize yttrium-cerium alloy hydrides. The phases examined by…
Strong interplay of fundamental order parameters in complex oxides are known to give rise to exotic physical phenomena. The 4d transition metal oxide SrRhO3 has generated much interest, but advances have been hindered by difficulties in…
Using a solid electrolyte to tune the carrier density in thin-film materials is an emerging technique that has potential applications in both basic and applied research. Until now, only materials containing small ions, such as protons and…
Geometrically frustrated solids with non-Euclidean reference metric are ubiquitous in biology and are becoming increasingly relevant in technological applications. Often they acquire a targeted con- figuration of incompatibility through…
Lithium-sulfur (Li-S) batteries offer substantial theoretical energy density gains over Li-ion bat-teries, a crucial factor for transportation electrification. In addition, sulfur is an earth-abundant, inexpensive material obtainable from…
We discuss the problem of the optimal design of a micro-tubular fuel cell applying an inverse homogenization technique. Fuel cells are extremely clean and efficient electrochemical power generation devices, made up of a…
In this work, we report on the anisotropic etching characteristics of \b{eta}-Ga2O3 using triethylgallium (TEGa) performed in-situ within an MOCVD chamber. At sufficiently high substrate temperature, TEGa can act as a strong etchant for…
Electrical transport in oxide thin films under high pressure remains largely unexplored due to the lack of a universal experimental strategy. Here we develop an approach that enables high-pressure transport measurements in freestanding…
Despite advancements in silicon-based anodes for high-capacity lithium-ion batteries, their widespread commercial adoption is still hindered by significant volume expansion during cycling, especially at high active mass loadings crucial for…
Voltage control of interfacial magnetism has been greatly highlighted in spintronics research for many years, as it might enable ultra-low power technologies. Among few suggested approaches, magneto-ionic control of magnetism has…
Two-dimensional layered and atomically thin elemental superconductors may be key ingredients in next-generation quantum technologies, if they can be stabilized and integrated into heterostructured devices under ambient conditions. However,…
Sulfide-based glasses and glass-ceramics showing high ionic conductivities and excellent mechanical properties are considered as promising solid-state electrolytes. Nowadays, the computational material techniques with the advantage of low…
Zirconium nitride (ZrN) is a refractory material with good mechanical and thermal properties. It is therefore a good candidate for hard surface treatment at high temperature. In this work, we report the growth and characterization of ZrN by…
Artificial electrostatic potentials can be present in supercells constructed for atomistic simulations of surfaces and interfaces in ionic crystals. Treating the ions as point charges, we systematically derive an electrostatic formalism for…
Recent results on laser wakefield acceleration in tailored plasma channels have underlined the importance of controlling the density profile of the gas target. In particular it was reported that appropriate density tailoring can result in…
Changes in crystalline phases resulting from low-temperature ageing of different yttria doped and non-doped zirconia-toughened alumina composites and nanocomposites were investigated under controlled humidity and temperature conditions in…
Atomic-scale precision epitaxy of perovskite oxide superlattices provides unique opportunities for controlling the correlated electronic structures, activating effective control knobs for intriguing functionalities including…
Most ceramic materials are known for high fracture toughness while reacting highly brittle to physical deformation. Some advancements were made by utilizing the transformation toughening effect of Yttria-doped Zirconia. However, finding a…
Directional and self-propelled flow in open channels has a variety of applications, including microfluidic and medical devices, industrial filtration processes, fog-harvesting and condensing apparatuses. Here, we present versatile…
Solid-state lithium batteries have attracted considerable attention due to their potential to provide improved safety and higher energy density compared with conventional liquid electrolyte batteries. However, the stability of the interface…