Related papers: Modeling damage and fracture within strain-gradien…
We develop and demonstrate the first general computational tool for finite deformation static and dynamic dislocation mechanics. A finite element formulation of finite deformation (Mesoscale) Field Dislocation Mechanics theory is presented.…
The thermodynamic dislocation theory developed for non-uniform plastic deformations is used here for the analysis of twisted copper wires. With a small set of physical parameters that we expect to be independent of strain rate and…
The deformation behavior of nearly fully pearlitic, bainitic and martensitic steels during severe plastic deformation is summarized in this paper. Despite their significantly different yield stresses and their microstructures, their…
Plastic flow is conventionally treated as continuous in finite element (FE) codes, whether in isotropic, anisotropic plasticity, or crystal plasticity. This approach, derived from continuum mechanics, contradicts the intermittent nature of…
A theoretical and computational investigation is carried out of a dissipative model of rate-independent strain-gradient plasticity and its regularization. It is shown that the flow relation, when expressed in terms of the Cauchy stress, is…
The modeling of damage processes in materials constitutes an ill-posed mathematical problem which manifests in mesh-dependent finite element results. The loss of ellipticity of the discrete system of equations is counteracted by…
We examine the fracture mechanics of tearing graphene. We present a molecular dynamics simulation of the propagation of cracks in clamped, free-standing graphene as a function of the out-of-plane force. The geometry is motivated by…
Stochastic models for pore collapse in granular materials are developed. First, a general fluctuating stress-strain relation for a plastic flow rule is derived. The fluctuations account for non-associativity in plastic deformations…
We investigate the fragmentation process of solid materials with crystalline and amorphous phases using the discrete element method. Damage initiates inside spherical samples above the contact zone in a region where the circumferential…
Three-dimensional X-ray diffraction (3DXRD) has been used to measure, in-situ, the evolution of $\sim 1800$ grains in a single phase low carbon ferritic steel sample during uniaxial deformation. The distribution of initial residual grain…
The stress-driven motion of dislocations in crystalline solids, and thus the ensuing plastic deformation process, is greatly influenced by the presence or absence of various point-like defects such as precipitates or solute atoms. These…
In the present paper a plastic-damage model for concrete is discussed. Based on the fact that for isotropic materials the elastic trial stress and the projected plastic stress states have the same eigenvec-tors, the loading surface is…
The mechanical properties and long-term structural reliability of crystalline materials are strongly influenced by microstructural features such as grain size, morphology, and crystallographic texture. These characteristics not only…
Excessive loads near wounds produce pathological scarring and other complications. Presently, stress cannot easily be measured by surgeons in the operating room. Instead, surgeons rely on intuition and experience. Predictive computational…
The influence of phase transformation-induced plastic deformation in Pd|H system on the electrode surface was investigated. Since the Pd surface is subject of severe plastic deformation during this process, the structure and roughness of…
Dynamic fracture in a wide class of materials reveals "fracture energy" $\Gamma$ much larger than the expected nominal surface energy due to the formation of two fresh surfaces. Moreover, the fracture energy depends on the crack velocity,…
This work outlines a diffuse interface method for the study of fracture and fragmentation in ductile metals at high strain-rates in Eulerian finite volume simulations. The work is based on an existing diffuse interface method capable of…
We present a phase field formulation for fracture in functionally graded materials (FGMs). The model builds upon homogenization theory and accounts for the spatial variation of elastic and fracture properties. Several paradigmatic case…
The effect of substrate was studied using nanoindentation on thin films. Soft films on hard substrate showed more pile up than usual which was attributed to the dislocation pile up at the film substrate interface. The effect of tip blunting…
Based on spatial-temporal resolved measurements of the stress field at crack tip based on polarized optical microscopy (str-POM), the stress analysis approach to elastomeric fracture uncovers new insights. We show new phenomenology in…