Related papers: Ultra-Low Noise Amplifier Design for Magnetic Reso…

The present article primarily focuses on the design of an ultra-low-noise amplifier specifically tailored for quantum applications. The circuit design places a significant emphasis on improving the noise figure, as quantum-associated…

A low-noise amplifier (LNA) amplifies a very low-power signal without significantly degrading its signal-to-noise ratio. This paper provides the design of a linear low noise amplifier with the transistor BFP 640 using bilateral approach…

This paper presents the analysis, design, fabrication, and measurement of an integrated low-noise amplifier (LNA) implemented using a 130 nm CMOS technology, operating in the 2.4 GHz band. The LNA is a crucial component in the performance…

This paper presents a low-noise amplifier (LNA) that was developed for a new radio telescope comprised of 512 parabolic dish antennas. The LNA closely interfaces to a custom-made antenna feed with an impedance co-designed to provide noise…

This study undertakes the theoretical design, CAD modeling, realization, and performance analysis of a microwave low-noise amplifier (LNA) which has been accurately developed for operation at 3.0 GHz (S-band). The objective of this research…

Noise level frequently set the basic limit on the smallest signal. New noise reduction technology and amplifiers voltage-noise density, yet still offer high speed, high accuracy, and low power solution. Low noise amplifiers always play a…

A Low-Power Variable Gain (VG) mm-Wave Low Noise Amplifier (LNA) is designed and simulated in a 28-nm CMOS process. The LNA utilizes a simple, yet novel, technique presented in this paper to vary the small-signal output resistance to…

This paper studies an architecture with digitally controllable gain and power consumption to mitigate the impact of process variations on CMOS low-noise amplifiers (LNAs). A \SI{130}{nm}, \SI{1.2}{V} LNA implementing the proposed…

A low power cascode SiGe BiCMOS low noise amplifier (LNA) with current reuse and zero-pole cancellation is presented for ultra-wideband (UWB) application. The LNA is composed of cascode input stage and common emitter (CE) output stage with…

As the Internet of Things (IOT) is growing rapidly, there is an emerging need to facilitate development of IOT devices in the design cycle while optimized performance is obtained in the field of operation. This paper develops…

To achieve the low noise and wide bandwidth required for millimeter wavelength astronomy applications, superconductor-insulator-superconductor (SIS) mixer based receiver systems have typically been used. This paper investigates the…

This paper investigates the impact of technological constraints on passive elements in the design of inductively degenerated CMOS low-noise amplifiers (LNAs). A theoretical analysis is combined with circuit simulations in a 130-nm CMOS…

This article introduces a design of a Low Noise Amplifier (LNA), for the field of diamond particle detectors. This amplifier is described from simulation to measurements, which include pulses from {\alpha} particles detection. In hadron…

In high-performance RF transceivers the thrust of has been on lower noise LNAs and high-power high-speed PAs. The performance trade-off has forced many solutions to have the LNA and PA on a separate die compared to the rest of baseband.…

Large-scale superconducting quantum computers require massive numbers of high-performance cryogenic low-noise amplifiers (cryo-LNA) for qubit readout. Here we present a C-Band monolithic microwave integrated circuit (MMIC) cryo-LNA for this…

In this paper a new design of MMIC based LNA is outlined. This design uses a discrete 100-nm InP HEMT placed in front of an existing InP MMIC LNA to lower the overall noise temperature of the LNA. This new approach known as the Transistor…

The quest to enhance the sensitivity of electron spin resonance (ESR) is an ongoing challenge. One potential strategy involves increasing the frequency, for instance, moving from Q-band (approximately 35 GHz) to W-band (approximately 94…

We report on the design and characterization of a high-power amplifier with an output power of 36.5 dBm for a frequency range of 50 MHz to 1000 MHz with a total gain of 40 dB. The amplifier is optimized for driving acousto-optic and…

We report on the noise of a lumped element Direct Current Superconducting Quantum Interference Device amplifier. We show that the noise temperature in the 4 GHz-8 GHz range over ranges of 10's of MHz is below 1 kelvin (three photons of…

Purpose: Low-field MRI systems operate at single MHz-range frequencies, where signal losses are primarily dominated by thermal noise from the radio-frequency (RF) receive coils. Achieving operation close to this limit is essential for…