Related papers: Low-cost high-efficiency solar steam generation by…
Solar steam generation technology can utilize abundant and renewable solar energy for many applications. In this work, we proposed a solar steam generator using wick material with wrapped graphene nanoparticles, and the energy efficiency…
Many efforts have been dedicated to improve the solar steam generation by using a bi-layer structure. In this paper, a two-dimensional mathematical model describing the water evaporation in a bi-layer structure is firstly established and…
We report the development of graphite-based solar cells using a simple method and low cost materials. Suspension of graphite powder in mineral water was simply dropped onto the surface of fluorine-doped tin oxide glass (FTO) to form a thick…
Thermophotovoltaic systems in principle enable utilization of heat that is usually regarded as wasted energy. However, the wavelength selectivity of the thermal emitter required for high efficiencies is rather difficult to control with…
We propose a new concept for the design of high-efficiency photocells based on ultra-thin (submicron) semiconductor films of controlled thickness. Using a microscopic model of a thin dielectric layer interacting with incident…
Solar evaporation is important for many applications such as desalination, power generation and industrial drying. Recently, some studies on evaporation reported obtaining high energy efficiency and evaporation rate, which are based on…
The bi-layered structure has drawn a wide interest due to its good performance in solar steam generation. In this work, we firstly develop a calculation model which could give a good prediction of experimental results. Then, this model is…
Thin-film solar cells that are considered as the second generation of solar cells are known for their low cost and acceptable efficiency. In this technology, semiconductor layers with a thickness of micrometer are deposited on thick enough…
A new approach is introduced to significantly improve the performance of thermophotovoltaic (TPV) systems by using low-dimensional thermal emitters and photovoltaic (PV) cells. By reducing the thickness of both the emitter and the PV cell,…
Electric power may, in principle, be generated in a highly efficient manner from heat created by focused solar irradiation, chemical combustion, or nuclear decay by means of thermionic energy conversion. As the conversion efficiency of the…
Solar-driven interfacial steam generation for desalination has attracted broad attention. However, a significant challenge still remains for achieving a higher evaporation rate and high water quality, together with a cost-effective and…
We propose a concentrated thermionic emission solar cell design, which demonstrates a high solar-to-electricity energy conversion efficiency larger than 10\% under 600 sun, by harnessing the exceptional electrical, thermal and radiative…
Thin film solar cells have been attractive for decades in advanced green technology platforms due to its possibilities to be integrated with buildings and on-chip applications. However, the bottleneck issues involved to consider the current…
Thin-film thermoelectric generators with a novel folding scheme are proposed for large-area, low energy-density applications. Both the electrical current and heat transfer are in the plane of the thermoelectric thin-film, yet the heat…
Nano-scaled metallic or dielectric structures may provide various ways to trap light into thin-film solar cells for improving the conversion efficiency. In most schemes, the textured active layers are involved into light trapping structures…
As the availability of weather-dependent, zero marginal cost resources such as wind and solar power increases, a variety of flexible electricity loads, or `demand sinks', could be deployed to use intermittently available low-cost…
Elemental selenium is a promising wide-bandgap ($E_\mathrm{G}\approx$ 1.95 eV) photovoltaic material for the next generation of thin-film solar cells. To realize high-efficiency selenium solar cells, it is crucial to optimize the…
Solar-thermal evaporation, a traditional steam generation method for solar desalination, has received numerous attentions in recent years due to the significant increase in efficiency by adopting interfacial evaporation. While most of the…
Micro Porosity Sintered wick is made from metal injection molding processes, which provides a wick density with micro scale. It can keep more than 53 % working fluid inside the wick structure, and presents good pumping ability on working…
A PEM micro fuel cell system is described which is based on self-breathing PEM micro fuel cells in the power range between 1 mW and 1W. Hydrogen is supplied with on-demand hydrogen production with help of a galvanic cell, that produces…