Related papers: ADC Bit Allocation under a Power Constraint for Mm…
The millimeter wave (mmWave) frequency band is seen as a key enabler of multi-gigabit wireless access in future cellular networks. In order to overcome the propagation challenges, mmWave systems use a large number of antenna elements both…
Millimeter wave (mmWave) systems are emerging as an essential technology to enable extremely high data rate wireless communications. The main limiting factors of mmWave systems are blockage (high penetration loss) and deafness (misalignment…
Motivated by the demand for energy-efficient communication solutions in the next generation cellular network, a mixed-ADC architecture for massive multiple input multiple output (MIMO) systems is proposed, which differs from previous works…
Network-assisted full-duplex (NAFD) distributed massive multiple input multiple output (M-MIMO) enables the in-band full-duplex with existing half-duplex devices at the network level, which exceptionally improves spectral efficiency. This…
Millimeter wave (mmWave) cellular systems will enable gigabit-per-second data rates thanks to the large bandwidth available at mmWave frequencies. To realize sufficient link margin, mmWave systems will employ directional beamforming with…
Multiple-input multiple-output (MIMO) millimeter wave (mmWave) systems are vulnerable to hardware impairments due to operating at high frequencies and employing a large number of radio- frequency (RF) hardware components. In particular,…
This paper considers a multipair amplify-and-forward massive MIMO relaying system with one-bit ADCs and one-bit DACs at the relay. The channel state information is estimated via pilot training, and then utilized by the relay to perform…
High power consumption and hardware cost are two barriers for practical massive multiple-input multiple-output (mMIMO) systems. A promising solution is to employ low-resolution analog-to-digital converters (ADCs). In this paper, we consider…
Hybrid analog and digital beamforming has emerged as a key enabling technology for millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) communication systems since it can balance the trade-off between system performance…
An adaptive joint power allocation (JPA) and linear receiver design algorithm using the minimum bit error rate (MBER) criterion for a cooperative Multiple-Input Multiple-Output (MIMO) network is proposed. The system employs multiple relays…
Millimeter wave (mmWave) MIMO will likely use hybrid analog and digital precoding, which uses a small number of RF chains to avoid energy consumption associated with mixed signal components like analog-to-digital components not to mention…
This work investigates the downlink performance of a multi-cell massive multiple-input multiple-output (MIMO) system that employs one-bit analog-to-digital converters (ADCs) and digital-to-analog converters (DACs) in the receiving and…
Using a very low-resolution analog-to-digital convertor (ADC) unit at each antenna can remarkably reduce the hardware cost and power consumption of a massive multiple-input multiple-output (MIMO) system. However, such a pure low-resolution…
The use of one-bit analog-to-digital converters (ADCs) is a practical solution for reducing cost and power consumption in massive Multiple-Input-Multiple-Output (MIMO) systems. However, the distortion caused by one-bit ADCs makes the data…
This paper investigates the hybrid precoding design for millimeter wave (mmWave) multiple-input multiple-output (MIMO) systems with finite-alphabet inputs. The mmWave MIMO system employs partially-connected hybrid precoding architecture…
As communication systems advance towards the future 6G era, the incorporation of large-scale antenna arrays in base stations (BSs) presents challenges such as increased hardware costs and energy consumption. To address these issues, the use…
This paper addresses the problem of uplink transmit power optimization in distributed massive multiple-input multiple-output systems, where remote radio heads (RRHs) are equipped with 1-bit analog-to-digital converters (ADCs). First, in a…
The use of base stations (BSs) and access points (APs) with a large number of antennas, called Massive MIMO (multiple-input multiple-output), is a key technology for increasing the capacity of 5G networks and beyond. While originally…
Hybrid analog/digital architectures and receivers with low-resolution analog-to-digital converters (ADCs) are two low power solutions for wireless systems with large antenna arrays, such as millimeter wave and massive MIMO systems. Most…
This letter revisits the channel estimation problem for MIMO systems with one-bit analog-to-digital converters (ADCs) through a novel algorithm--Amplitude Retrieval (AR). Unlike the state-of-the-art methods such as those based on one-bit…