Related papers: Numerical simulation of InGaN Schottky solar cell

Graphene-silicon Schottky junction (GSJ) which has the potential for large-scale manufacturing and integration can bring new opportunities to Schottky solar cells for photovoltaic (PV) power conversion. However, the essential power…

First-principles calculations are performed to study the structural and optoelectronic properties of the newly synthesized nonisovalent and lattice-matched (Si2)0.6(AlP)0.4 alloy [T. Watkins et al., J. Am. Chem. Soc. 2011, 133, 16212.] We…

Zinc phosphide (Zn3P2) has had a long history of scientific interest largely because of its potential for earth-abundant photovoltaics. To realize high-efficiency Zn3P2 solar cells, it is critical to understand and control point defects in…

Wide-gap Cu(In,Ga)S2 solar cells with In2O3:Sn (ITO) as transparent back contact are evaluated for the application as top cells in tandem devices. The effect of Na on the solar cell performance is investigated by supplying additional Na by…

III-Nitride light emitting diodes (LEDs) are widely used in a range of high efficiency lighting and display applications, which have enabled significant energy savings in the last decade. Despite the wide application of GaN LEDs, transport…

InGaN light-emitting diodes (LEDs) are more efficient and cost effective than incandescent and fluorescent lighting, but lattice mismatch limits the thickness of InGaN layers that can be grown on GaN without performance-degrading…

Power-conversion efficiency is a critical factor for the wider adoption of solar-cell modules. Thin-film solar cells are cheap and easy to manufacture, but their efficiencies are low compared to crystalline-silicon solar cells and need to…

Schottky barrier height and the ideality factor $\eta$ are established for the first time in the single phase (Ga,Mn)N using a vertical geometry device. The material has been heteroepitaxially grown on commercially available low threading…

We demonstrate four and two-terminal perovskite-perovskite tandem solar cells with ideally matched bandgaps. We develop an infrared absorbing 1.2eV bandgap perovskite, $FA_{0.75}Cs_{0.25}Sn_{0.5}Pb_{0.5}I_3$, that can deliver 14.8 %…

We investigated the current-voltage characteristic of InAs/GaAs quantum dot intermediate band solar cells (QD IBSCs) with different n-type doping density in the QD layer. The n-type doping evidently increases the open circuit voltage,…

Lead-free all-inorganic halide perovskite solar cells (PSCs) have emerged as a promising alternative to toxic lead-based solar cells and organic solar cells, which have limited stability. This work explores such a PSC with sodium tin…

Photogalvanic solar cells, the original dye based solar cell, have yet to fulfill their promise as a low fabrication cost, scalable energy conversion system. The efficient performance of photogalvanic cells relies on high dye solubility and…

The Shockley and Queisser limit, a well-known efficiency limit for a solar cell, is based on unrealistic physical assumptions and its maximum limit is seriously overestimated. To understand the power loss mechanisms of record-efficiency…

SCAPS 1-D was used for the simulation of lead-free environmentally benign methylammonium tin-iodide (CH3NH3SnI3) based solar cell. Indium sulphide (In2S3) was utilized as the electron transport layer (ETL) for its high carrier mobility and…

Ion migration in halide perovskites is a key factor limiting the operational stability of solar cells due to formation of halogen ion enriched domains and accumulation layers. The present work demonstrates the manifestation of ion migration…

Here, we propose titanium nitride (TiN) as an alternative plasmonic material for an on-chip silicon plasmonic Schottky photodetector that is based on an internal photoemission process and operating at telecom wavelengths. The examined…

One effective way to prevent toxicity and improve the stability of materials for photovoltaic applications is to exclude lead and organic molecules from perovskite materials. Specifically, the CsSn1-xGexI3 appears to be a promising…

In this paper we conduct numerical simulation of CdS/CIGS solar cells by use of the AMPS-1D software aiming to formulate the optimal design of the new multi-junction tandem solar cell providing its most efficient operation. We start with…

Since hydrogen fuel involves the highest energy density among all fuels, production of this gas through the solar water splitting approach has been suggested as a green remedy for greenhouse environmental issues due to extensive consumption…

Despite the youthfulness of hybrid halide perovskite solar cells, their efficiencies are currently comparable to commercial silicon and have surpassed quantum-dots solar cells. Yet, the scalability of these devices is a challenge due to…