Related papers: Analysis Of SnS2 Buffer Layer And SnS Back Surface…
Alloying small quantities of silver into Cu(In,Ga)Se2 was shown to improve the efficiency for wide and low band gap solar cells. We study low band gap industrial Cu(In,Ga)(S,Se)2 absorbers, substituting less than 10% of the copper with…
We propose a frequency selective light trapping scheme that enables the creation of more visually-transparent and yet simultaneously more efficient semitransparent solar cells. A nanoparticle scattering layer and photonic stack back…
We optimize the deposition of CH3NH3PbI3 perovskite into mesoporous electrodes consisting of anodic TiO2 nanotube layers. By a simple spin coating approach, complete filling of the tube scaffolds is obtained, that leads to interdigitated…
A spatial stochastic model is developed which describes the 3D nanomorphology of composite materials, being blends of two different (organic and inorganic) solid phases. Such materials are used, for example, in photoactive layers of hybrid…
Cn2 profile monitoring usually makes use of wavefront slope correlations or of scintillation pattern correlations. Wavefront slope correlations provide sensitivity to layers close to the receiving plane. In addition, scintillation…
On the road towards next generation high efficiency solar cells, the ternary Indium Gallium Nitride (InGaN) alloy is a good passenger since it allows to cover the whole solar spectrum through the change in its Indium composition. The choice…
This study explores the impact of an optimized amorphous silicon (a-Si) buffer layer on AlxIn1-xN-on-Si(100) heterojunction solar cells, with Al content varying from 0% (InN) to 55%. The buffer layer improves the structural quality of the…
Both tin monosulfide (SnS) and tin disulfide (SnS2) are thermodynamically stable layered materials with potential for spin-valleytronic devices and photodetectors. Notably, monolayer SnS, owing to its low symmetry, exhibits interesting…
Record efficiency in chalcopyrite-based solar cells Cu(In,Ga)(S,Se)2 is achieved using a gallium gradient to increase the band gap of the absorber towards the back side. Although this structure has successfully reduced recombination at the…
Metal sulfides are emerging as an important class of materials for photocatalytic applications, because of their high photo responsive nature in the wide visible light range. CdS in this class of materials, have a direct band gap of 2.4 eV,…
In this work we have employed density-functional theory with hybrid functionals to investigate the atomic and electronic structure of bare and hydrogenated Co doped ZnO nanowires. We find that in the absence of passivation on the nanowire…
In this work, we show that laser induced breakdown spectroscopy (LIBS) with a nanosecond pulse laser can be used to measure the copper and sodium content of CuIn(0.7)Ga(0.3)Se(2) (CIGS) thin film solar cells on molybdenum. This method has…
SCAPS-1D software ignores optical losses and recombination junction (RJ) layer in studying tandem solar cells (TSCs). This paper presents an optoelectronic study of a perovskite/Silicon TSC, comparing the effects of using two different…
Two-terminal tandem cell architectures are believed to be an effective way to further improve the power conversion efficiency in solution processed photovoltaics. To design an efficient tandem solar cell, two key issues need to be…
We report on the passivation of surface defects of ZnO nanorods by surface layer deposition. ZnO nanorods and ZnS-ZnO hybrid nanostructures are grown on FTO coated glass substrate by chemical bath deposition method. XRD spectrum of ZnO…
Cu2ZnSnS4 (CZTS) is a promising material as an absorber in photovoltaic applications. The measured efficiency, however, is far from the theoretically predicted value for the known CZTS phases. To improve the understanding of this…
Transition metal dichalcogenide (TMD) materials have emerged as promising candidates for thin film solar cells due to their wide bandgap range across the visible wavelengths, high absorption coefficient and ease of integration with both…
This study explores the potential of MoS$_2$ polymorphs, specifically the semiconducting 2H phase and the metallic 1T$^\prime$ phase, as anchoring materials to enhance the electrochemical performance of lithium-sulfur (Li--S) batteries.…
Copper nanowires are widely used as on-chip interconnects due to superior conductivity. However, with aggressive Cu interconnect scaling, the diffusive surface scattering of electrons drastically increases the electrical resistivity. In…
Enhancing the transport of oxygen anions in the cathode while maintaining surface stability is essential for improving the performance of intermediate-temperature solid oxide fuel cells (IT-SOFCs). This study investigates a novel cathode…