Related papers: Does a dissolution-precipitation mechanism explain…
The solutional origin of limestone caves was recognized over a century ago, but the short penetration length of an undersaturated solution made it seem impossible for long conduits to develop. This is contradicted by field observations,…
We present a thermodynamically consistent constitutive model for fluid-saturated sediments, spanning dense to dilute regimes, developed from the basic balance laws for two phase-mixtures. The model can represent various limiting cases, such…
A number of dense particle suspensions experience a dramatic increase in viscosity with the shear stress, up to a solid-like response. This shear-thickening process is understood as a transition under flow of the nature of the contacts,…
Iron is a candidate to replace cobalt in WC hardmetals, due to its lower cost and toxicity. A WC-FeCr hardmetal was compression tested at 900-1200 {\deg}C. Particular attention is paid to the steady-state creep rates and stress-exponents…
We numerically investigate the athermal creep deformation of amorphous materials having a wide range of stability. The imposed shear stress serves as the control parameter, allowing us to examine the time-dependent transient response…
The moisture absorption in granulated materials used in foundry technologies is analyzed. The absorption process has a diffusive behavior mainly. A simple experimental technique, in which the wet weight increment was recorded as the…
Shear thickening denotes the reversible increase in viscosity of a suspension of rigid particles under external shear. This ubiquitous phenomenon has been documented in a broad variety of multiphase particulate systems, while its…
Strain hardening is a key feature observed in many rocks deformed in the so-called ``semi-brittle'' regime, where both crystal plastic and brittle deformation mechanisms operate. Dislocation storage has long been recognised as a major…
The universal instability mechanism in an ascending moist air flow is theoretically proposed and analyzed. Its origin comes to the conflict between two processes: the increasing of pressure forcing applied to the boundary layer and the…
Stress corrosion cracking (SCC) is a form of failure in metals that is present mostly in systems where humidity contact and mechanical load play a key role. Therefore, prediction of the combined effect is desired. There are models based on…
Precipitation extremes produced by convection have been found to intensify with near-surface temperatures at a Clausius-Clapeyron rate of $6$ to $7\%$ K$^{-1}$ in simulations of radiative-convective equilibrium (RCE). However, these…
Fine particle suspensions (such as cornstarch mixed with water) exhibit dramatic changes in viscosity when sheared, producing fascinating behaviors that captivate children and rheologists alike. Recent examination of these mixtures in…
A correlation is established between the macro-scale friction regimes of metals and a transition between two dominant atomistic mechanisms of deformation. Metals tend to exhibit bi-stable friction behavior -- low and converging or high and…
The impact dynamics between wet surfaces, which dominates the mechanical properties of wet granular matter, is studied both experimentally and theoretically. It is shown that the hysteretic formation and rupture of liquid capillary bridges…
The invasion of air into porous systems in drying processes is often localized in soft materials, such as colloidal suspensions and granular pastes, and it typically develops in the form of cracks before ordinary drying begins. To…
Three-dimensional, time-dependent direct simulations of step emulsification micro-devices highlight two essential mechanisms for droplet formation: first, the onset of an adverse pressure gradient driving a back-flow of the continuous phase…
During plastic deformation, metals change shape while continuously becoming stronger. The microscopic origin of these processes lies in the proliferation and movement of line defects, dislocations, and the subsequent self-organisation and…
This study aims to identify and isolate the role of properties of water with respect to the shape of the first desorption isotherm of hardened cement pastes. It has been observed that desorption occurs not only by receding meniscus but is…
Yield stress fluids display complex dynamics, in particular when driven into the transient regime between the solid and the flowing state. Inspired by creep experiments on dense amorphous materials, we implement mesocale elasto-plastic…
To examine the microstructural evolution that occurs during transient creep, we deformed olivine aggregates to different strains that spanned the initial transient deformation. Two sets of samples with different initial grain sizes of 5…