Related papers: Crack Formation in Ceramic Films Used in Solid Oxi…
Magnetron sputtering has also been used to deposit thin films of some materials and it has significant technological importance. A modeling on deposition of epitaxial thin films of Yttrium Stabilized Zirconia (YSZ) was done the diffusion of…
The effects of substrate treatment, temperature and composition on the surface morphology of Ni-Cr thin films grown on MgO(001) are studied by scanning tunneling microscopy (STM) and atomic force microscopy (AFM). A combination of…
The pattern development of multiple cracks in extremely anisotropic solids such as bilayer or multilayer two-dimensional (2D) crystals contains rich physics, which, however, remains largely unexplored. We studied crack interaction across…
Cracks develop various surface patterns as they propagate in three-dimensional (3D) materials. Facet formation in nominally tensile (mode-I) fracture emerge in the slow, non-inertial regime and oftentimes takes the form of surface steps. We…
We study how single-crystal chromium films of uniform thickness on W(110) substrates are converted to arrays of three-dimensional (3D) Cr islands during annealing. We use low-energy electron microscopy (LEEM) to directly observe a kinetic…
When silica-filled rubber compounds are deformed, structural modifications in the material's bulk lead to irreversible damage, the most significant of which is cavitation appearing within the interfaces of interconnected polymer and filler…
On highly oxygen deficient thin films of hafnium oxide (hafnia, HfO$_{2-x}$) contaminated with adsorbates of carbon oxides, the formation of hafnium carbide (HfC$_x$) at the surface during vacuum annealing at temperatures as low as 600…
Surface wrinkling is an instability mode that is often observed in a wide variety of multilayer tubes under bending deformation. When the degree of applied bending exceeds a critical value, wrinkles appear at the intrados of the tube and…
Two novel single-period cracks were observed in experiments of cutting a folded sheet with a blunt object and tearing a thin brittle sheet under the guidance of a meterstick. Additionally, we observed a period-doubling crack in the tearing…
Upon mechanical loading, granular materials yield and undergo plastic deformation. The nature of plastic deformation is essential for the development of the macroscopic constitutive models and the understanding of shear band formation.…
The present work is essentially focused on the study of optical and structural properties of hydrogenated amorphous silicon thin films (a-Si:H) prepared by radio-frequency cathodic sputtering. We examine separately the influence of hydrogen…
We demonstrate spontaneous wrinkling as a transient dynamical pattern in thin freely floating smectic liquid-crystalline films. The peculiarity of such films is that, while flowing liquid-like in the film plane, they cannot quickly expand…
In this study, we propose a laboratory-scale methodology, based on X-ray micro-tomography and caesium (Cs) as a contrast agent, to advance the understanding of cracking due to alkali-silica reaction (ASR) in concrete. The methodology allows…
Two-dimensional simulations are used to explore topological transitions that occur during the formation of films grown from grains that are seeded on substrates. This is done for a relatively large range of the initial value $\Phi_s$ of the…
The present review is intended to revisit the advances and debates in the comprehension of the mechanisms of subcritical crack propagation in silicate glasses almost a century after its initial developments. Glass has inspired the initial…
It has been a widely growing interest in using silicon carbide (SiC)in high-power electronic devices. Yet, SiC wafers may contain killer defects that could reduce fabrication yield and make the device fall into unexpected failures. To…
An elastic-visco-plastic thermomechanical model for the simulation of cold forming and subsequent sintering of ceramic powders is introduced and based on micromechanical modelling of the compaction process of granulates. Micromechanics…
A novel growth technique for low density, non-icosahedral carbon onion-like structures on Cu surface is described. The technique differs with the formation of carbon onions inside the C1+ implanted metal surfaces at high temperatures with…
Ever since the very first human-made knapped tools, the control of fracture propagation in brittle materials has been a vector of technological development. Nowadays, a broad range of applications relies on crack propagation control, from…
Spin-orbit coupling (SOC), the core of numerous condensed-matter phenomena such as nontrivial band gap, magnetocrystalline anisotropy, etc, is generally considered to be appreciable only in heavy elements, detrimental to the synthetization…