Related papers: Breakdown voltage of metal-oxide resistors in liqu…
High voltage breakdown in liquid argon is an important concern in the design of liquid argon time projection chambers, which are often used as neutrino and dark matter detectors. We have made systematic measurements of breakdown voltages in…
We report on the results of a high voltage test in liquid argon in order to measure its dielectric rigidity. Under stable conditions and below the boiling point, liquid argon was found to sustain a uniform electric field of 100 kV/cm,…
In this paper we present results on measurements of the dielectric strength of liquid argon near its boiling point and cathode-anode distances in the range of 0.1 mm to 40 mm with spherical cathode and plane anode. We show that at such…
In this paper we demonstrate the capability of high voltage varistors and gas discharge tube arrestors for use as surge protection devices in liquid argon time projection chamber detectors. The insulating and clamping behavior of each type…
We present a study on the dependence of electric breakdown discharge properties on electrode geometry and the breakdown field in liquid argon near its boiling point. The measurements were performed with a spherical cathode and a planar…
Breakdown voltages of a capacitively coupled radio frequency argon discharge at 27 MHz are studied. We use a one-dimensional electrostatic PIC code to investigate the effect of changing the secondary emission properties of the electrodes on…
Using the metal-insulator transition that takes place as a function of carrier density at the LaAlO$_3$-SrTiO$_3$ interface, oxide diodes have been fabricated with room-temperature breakdown voltages of up to 200 V. With applied voltage,…
Conditioning of a metal structure in a high-voltage system is the progressive development of resistance to vacuum arcing over the operational life of the system. This is, for instance, seen during the initial operation of radio frequency…
As noble liquid time projection chambers grow in size their high voltage requirements increase, and detailed, reproducible studies of dielectric breakdown and the onset of electroluminescence are needed to inform their design. The Xenon…
Silicon pixel sensors manufactured using commercial CMOS processes are promising instruments for high-energy particle physics experiments due to their high yield and proven radiation hardness. As one of the essential factors for the…
High voltage (~2 kV) AlGaN-channel HEMTs were fabricated with 64% Aluminum composition in the channel. The average on-resistance was ~75 ohm. mm (~21 miliohm. cm^2) for LGD = 20 microns. Breakdown voltage reached >3 kV (tool limit) before…
The electrical resistivity of liquid hydrogen has been measured at the high dynamic pressures, densities and temperatures that can be achieved with a reverberating shock wave. The resulting data are most naturally interpreted in terms of a…
The resistivity of polycrystalline chemical vapor deposition diamond sensors is studied in samples exposed to fluences relevant to the environment of the High Luminosity Large Hadron Collider. We measure the leakage current for a range of…
The degradation of ultrathin oxide layers in the presence of a stress voltage is modeled in terms of two antagonist percolation processes taking place in a random resistor network. The resistance and leakage current fluctuations are studied…
This study measures the voltage at which flashover occurs in compressed air for a variety of dielectric materials and lengths in a uniform field for DC voltages up to 100 kV. Statistical time lag is recorded and characterized, displaying a…
The proliferation of liquid argon time projection chamber detectors makes the characterization of the dielectric properties of liquid argon a critical task. To improve understanding of these properties, a systematic study of the breakdown…
Voltages above a hundred kilo-volt will be required to generate the drift field of future very large liquid Argon Time Projection Chambers. The most delicate component is the feedthrough whose role is to safely deliver the very high voltage…
Designs of high-voltage (HV) systems for creating a drift electric field in liquid argon TPCs are reviewed. In ongoing experiments systems capable of approx. 100 kV are realised for a drift field of 0.5-1 kV/cm over a length of up to 1.5 m.…
Ga2O3 Schottky barrier diodes featuring a field plate and a composite SiO2/SiNx dielectric layer beneath the field plate were fabricated, achieving a breakdown voltage of 2.4 kV at room temperature. Electrical performance and degradation…
We present a method to reach electric field intensity as high as 400 kV/cm in liquid argon for cathode-ground distances of several millimeters. This can be achieved by suppressing field emission from the cathode, overcoming limitations that…