Related papers: Multiaxial Fatigue Behaviour of A356-T6
Experimental investigations on the effect of thicknesses on mixed-mode I/II fracture are performed with an aluminum alloy with thicknesses of 2, 4, 8 and 14 mm. It is found that under pure-mode I loading condition, the loading capacity per…
Fatigue failure is ubiquitous in engineering applications. While the total fatigue life is critical to understanding a component's operational life, for safety, regulatory compliance, and predictive maintenance, the characterization of…
Fatigue failure of crystalline materials is a difficult problem in science and engineering, and recent results have shown that fatigue crack growth can occur in intermittent jumps which have fat-tailed distributions. As fatigue crack…
Composite structures must endure a great variety of multi-axial stress states during their lifespan while guaranteeing their structural integrity and functional performance. Understanding the fatigue behavior of these materials, especially…
Detecting mechanical fatigue of metallic components is always a challenge in industries. In this work, we proposed to monitor the low-cycle fatigue of a 6061 aluminum alloy based on internal friction (IF) measurement, which is realized by a…
Cast and HIP'ed \textgamma-TiAl 4522XD is being developed for use in jet engine low pressure turbine blades, where temperature variations occur through the flight cycle. The effects of temperature variations on fatigue cracking were…
The accumulated entropy is used to evaluate the initiation of crack in flat notched specimen made of stainless steel 304. Two notch radii have been studied to capture the thermography of crack initiation and measure accumulated heat…
Experimental Kitagawa analysis has been performed on A356-T6 containing natural and artificial defects. Results are obtained with a load ratio of R = -1 for three different loadings: tension, torsion and combined tension-torsion. The…
The damage mechanisms and load redistribution of high strength TC17 titanium alloy/unidirectional SiC fibre composite (fibre diameter = 100 $\mu$m) under high temperature (350 {\deg}C) fatigue cycling have been investigated in situ using…
This paper investigates correlation properties of fluctuations in fatigue crack growth of polycrystalline materials, such as ductile alloys, that are commonly encountered in structures and machinery components of complex electromechanical…
This work employs the Birnbaum--Saunders distribution to model the fatigue life of metallic materials under cyclic loading and compares it with the normal distribution. Fatigue-limit models are fitted to three datasets of unnotched…
Fatigue crack growth is decisive for the design of thin-walled structures such as fuselage shells of air planes. The cold rolling process, used to produce the aluminium sheets this structure is made of, leads to anisotropic mechanical…
The deformation and crack initiation mechanisms were analyzed in a textured AZ31B-O Mg alloy subjected to fully-reversed, strain-controlled cyclic deformation along the rolling direction after 50 cycles (approximately 33% of the fatigue…
In this work we propose a stochastic model for estimating the occurrence of crack initiations on the surface of metallic specimens in fatigue problems that can be applied to a general class of geometries. The stochastic model is based on…
A new phenomenological technique for using constant amplitude loading data to predict fatigue life from a variable amplitude strain history is presented. A critical feature of this reversal-by-reversal model is that the damage accumulation…
The accumulation of plastic deformation and flow localization in amorphous alloys under periodic shear are investigated using molecular dynamics simulations. We study a well-annealed binary mixture of one million atoms subjected to…
Electrode particle cracking is one of the main phenomena driving battery capacity degradation. Recent phase field fracture studies have investigated particle cracking behaviour. However, only the beginning of life has been considered and…
The additively manufactured titanium aluminide alloy TNM-B1 was characterized microstructurally and mechanically in the as-built and hot isostatically pressed (HIP) condition. Tensile and constant amplitude tests were performed at room…
The brittleness of an aluminide diffusion coating protecting a Ren\'e 125 Ni-based polycrystalline superalloy was investigated over a wide range of temperatures in its as-received and thermally aged form. Isothermal and thermal cycled aging…
Mode II fatigue crack growth under reversed shear and static biaxial compression was investigated in two bearing steels. Many aborted branches, quasi-orthogonal to the main crack, were observed along the crack face. The compressive stress…