Related papers: Feedback-controlled laser fabrication of micromirr…
We present a high-yield method for fabricating concave micromirror templates in silica using feedback-controlled CO2 laser ablation with precise in situ positioning. Real-time monitoring of the white-light emission generated during ablation…
We describe a micro-fabrication method to create concave features with ultra-low surface roughness in silica, either on the end facets of optical fibers or on flat substrates. The machining uses a single focused CO2 laser pulse. Parameters…
We report an experimental-computational study of the optical properties of plasma mirrors (PMs) at the incident laser frequency when irradiated directly at relativistic intensity (1e18 < I_0 < 1e19 W/cm^2) by near-normally incident (4…
We present the fabrication of exceptionally small-radius concave microoptics on fused silica substrates using CO2 laser ablation and subsequent reactive ion etching. The protocol yields on-axis near-Gaussian depressions with radius of…
We describe a technique for surface and sub-surface micro-machining of glass substrates using tightly focused femtosecond laser pulses at a wavelength of 1660 nm. Although silicate glass is normally transparent at this wavelength, the…
Reflection at relativistically moving plasma mirrors is a well-known approach for frequency conversion as an alternative to nonlinear techniques. A key issue with plasma mirrors is the need for a high carrier concentration, of order 10^21…
Control of laser writing in transparent dielectrics using temporal contrast of light pulses is demonstrated. Anisotropic nanopores in silica glass are produced by high-contrast of 10^7 femtosecond Yb: KGW laser pulses rather than…
Patient outcomes in the medical field are improving through the use and incorporation of robotics technology and laser physics, e.g., the use of optical fibers and lasers in micro-surgery. This paper describes the design and implementation…
An inexpensive, easily programmed microcontroller is demonstrated for the fast frequency stabilization of an infrared fiber laser. The microcontroller manages all digitalization and processing, with external circuitry only providing…
We report on fabricating high-fill-factor plano-convex spherical and square micro-lens arrays on fused silica glass surface using CO2 laser assisted reshaping technique. Initially, periodic micro-pillars have been encoded on the glass…
Optical resonators are increasingly important tools in science and technology. Their applications range from laser physics, atomic clocks, molecular spectroscopy, and single-photon generation to the detection, trapping and cooling of atoms…
We describe how active feedback routines can be applied at limited repetition rate (5 Hz) to optimize high-power $>10$ TW) laser interactions with clustered gases. Optimization of x-ray production from an argon cluster jet, using a genetic…
The dream of physico-chemists to control molecular reactions with light beyond electronic excitations pushes the development of laser pulse shaping capabilities in the mid-infrared (MIR) spectral range. Here, we present a compact optical…
On-chip optical trapping systems allow for high scalability and lower the barrier to access. Systems capable of trapping multiple particles typically come with high cost and complexity. Here we present a technique for making parabolic…
Over the past years, ultrafast lasers with average powers in the 100 W range have become a mature technology, with a multitude of applications in science and technology. Nonlinear temporal compression of these lasers to few- or even…
We have achieved stimulated laser cooling of thermal rubidium atomic beams on a silicon chip. Following pre-collimation via a silicon microchannel array, we perform beam brightening via a blue-detuned optical molasses. Owing to the small…
A semiconductor laser subject to delayed optical feedback is investigated in the limit of extremely intense feedback power. In a range of feedback polarization rotation angles the emission spectra of the laser reveal a giant gap with width…
We demonstrate a combination of optical and electronic feedback that significantly narrows the linewidth of distributed Bragg reflector lasers (DBRs). We use optical feedback from a long external fiber path to reduce the high-frequency…
Femtosecond laser micromachining (FLM) fabricated waveguides inherently form elliptical cores due to differences in focal spot size and the Rayleigh range of the microscope objective. Consequently, it is essential to study their propagation…
We realize mirror templates on the tips of optical fibers using a single-shot CO$_2$ laser ablation procedure. We perform a systematic study of the influence of the pulse power, pulse duration, and laser spot size on the radius of…