Related papers: Evolution of Plastic Strain During a Flow Forming …
Long, shallow microchannels embedded in thick soft materials are widely used in microfluidic devices for lab-on-a-chip applications. However, the bulging effect caused by fluid--structure interactions between the internal viscous flow and…
The experimental results presented in this paper show the influence of the elastic deformation of porous solids on the adsorption process. With p+-type porous silicon formed on highly boron doped (100) Si single crystal, we can make…
Via simulations of flowing foam, we connect the high and intermediate density regimes of complex fluid flows into a consistent microscopic picture of deformation. While at and above the jamming transition, elastic correlations lead to…
In this paper the problem of a plane strain hydraulic fracture in elasto-plastic material is analyzed. The analysis is based on Finite Element Method computations of crack propagation and closure to simulate the Mini-Frac calibration test.…
The microstructure and mechanical properties of materials saturate to steady states after severe plastic deformation (SPD). Despite the well-known effect of temperature on the steady-state microstructure, there is no general agreement on…
We numerically study confined channel foam flow around an obstacle using a two-dimensional bubble model, inspired by experiments performed in the same geometry. We systematically vary the polydispersity, the external driving force, and the…
We study the uniaxial compressive behavior of disordered colloidal free-standing micropillars composed of a bidisperse mixture of 3 and 6 um polystyrene particles. Mechanical annealing of confined pillars enables variation of the packing…
The distribution of local residual stresses (threshold to instability) that controls the statistical properties of plastic flow in athermal amorphous solids is examined with an atomistic simulation technique. For quiescent configurations,…
A new model has been developed to estimate the flow stress under hot deformation conditions up to the peak of the stress-strain curves. The model is constructed on the basis of the general form of sine functions by introducing an additional…
We study the elastic response of concentrated suspensions of rigid wire frame particles to a step strain. These particles are constructed from infinitely thin, rigid rods of length $L$. We specifically compare straight rod-like particles to…
Plasticity in soft amorphous materials typically involves collective deformation patterns that emerge upon intense shearing. The microscopic basis of amorphous plasticity has been commonly established through the notion of "Eshelby"-type…
We address the flutter instability of a flexible plate immersed in an axial flow. This instability is similar to flag flutter and results from the competition between destabilising pressure forces and stabilising bending stiffness. In…
Elastoplastic lattice models for the response of solids to deformation typically incorporate structure only implicitly via a local yield strain that is assigned to each site. However, the local yield strain can change in response to a…
We numerically investigate the stress distribution in pastes after horizontal rotation by using an elasto-plastic model. Residual stress remains as a memory of rotation. The stress in the circumferential direction increases after the…
Dense particle-fluid mixtures, or \emph{pastes}, are encountered in the production of various materials, including animal feed, human food, pharmaceuticals, and biomass for bioenergy. The flow behavior of such dense deformable particulate…
An extensive numerical campaign of particle mechanics calculations that predict microstructure formation and evolution during die compaction, up to relative densities close to one, of monodisperse plastic spheres that exhibit power-law…
We study the peculiar wrinkling pattern of an elastic plate stamped into a spherical mold. We show that the wavelength of the wrinkles decreases with their amplitude, but reaches a maximum when the amplitude is of the order of the thickness…
The role of heterogeneity in the plastic flow of thin ferrite specimens is investigated in this study. This is done through a recently introduced quasi-2D experimental-numerical framework that allows for a quantitative comparison of the…
By comparing the response to external strains in metallic glasses and in Lenard-Jones glasses we find a quantitative universality of the fundamental plastic instabilities in the athermal, quasistatic limit. Microscopically these two types…
Precipitation of fine particles into the base material of a metal is a potent strengthening mechanism. This is numerically analyzed within a continuum framework based on a higher order strain gradient plasticity theory and by use of an…