Related papers: Air Entrainment by Viscous Contact Lines
On the basis of a previous theoretical approach to the plastic flow of highly refined materials, a physical explanation for diffusion bonding is essayed, which yields closed--form equations relating the bonding progress with time,…
After impact onto a smooth dry surface, a drop of viscous liquid initially spreads in the form of a thick lamella. If the drop splashes, it first emits a thin fluid sheet that can ultimately break up into droplets causing the splash.…
We present accurate measurements of the relative motion and deformation of two large bubbles released consecutively in a quiescent liquid confined in a thin-gap cell. Though the second bubble injected is smaller, we observed that in all…
Dewetting of liquid films on solid surfaces in the presence of evaporation is a common phenomenon and has been studied by many researchers. The previous numerical approach has revealed that evaporation accelerates the dewetting speed of the…
In this study, a partially submerged vertical cylinder is moved at constant velocity through water, which is initially at rest. During the motion, the wake behind the cylinder induces free-surface deformation. Eleven cylinders, with…
When a liquid drop falls on a solid substrate, the air layer in between them delays the occurrence of liquid--solid contact. For impacts on smooth substrates, the air film can even prevent wetting, allowing the drop to bounce off with…
Many objects in nature and industry are wrapped in a thin sheet to enhance their chemical, mechanical, or optical properties. There are similarly a variety of methods for wrapping, from pressing a film onto a hard substrate, to using…
We investigate experimentally the effect of wind on the dynamics of a viscous liquid film flowing down a thread. The liquid film is well-known to destabilize into an axisymmetric bead-like pattern in stagnant air. When the flowing film is…
We investigate the wicking in granular media by considering layers of grains at the surface of a liquid, and discuss the critical contact angle below which spontaneous impregnation takes place. This angle is found to be on the order of…
As a first step towards a microscopic understanding of the effective interaction between colloidal particles suspended in a solvent we study the wetting behavior of one-component fluids at spheres and fibers. We describe these phenomena…
The dip-coating geometry, where a solid plate is withdrawn from or plunged into a liquid pool, offers a prototypical example of wetting flows involving contact-line motion. Such flows are commonly studied using the lubrication approximation…
The passage of single air bubbles through the horizontal interface between miscible viscoplastic and Newtonian fluids, considering various combinations of densities and viscosities for the fluid layers, is studied computationally. The…
We study the dewetting of liquid films capped by a thin elastomeric layer. When the tension in the elastomer is isotropic, circular holes grow at a rate which decreases with increasing tension. The morphology of holes and rim stability can…
Stability of thin lubricating fluid coated slippery surfaces depends on the surface energy of the underlying solid surface. High energy solid surfaces, coated with thin lubricating oil, lead to the dewetting of the oil films upon depositing…
Current development of micro-scale technologies increases the interest to viscous flows with low and moderate Reynolds numbers. This work theoretically studies the entrainment flow of a viscous jet emerging from a plane wall into a half…
This fluid dynamic video entry to the 2011 APS-DFD Gallery of Fluid Motion details the transient evolution of the free surface surrounding the impact region of a low-viscosity laminar liquid jet as it enters a quiescent pool. The close-up…
Emulsion droplets of silicone oil (PDMS) are widely used as antifoaming agents but, in the case of non-aqueous foams, the mechanisms responsible for the bursting of the films separating the bubbles remain unclear. We consider a ternary…
The flow patterns created by a coherent horizontal liquid jet impinging on a vertical wall atmoderate flow rates (jet flowrates 0.5-4.0 L min-1, jet velocities 2.6-21 m s-1) are studied withwater on glass, polypropylene and…
Aqueous foams coarsen with time due to gas diffusion through the liquid. The mean bubble size grows, and small bubbles vanish. However, coarsening is little understood for foams with an intermediate liquid content, particularly in the…
As the liquid jet plunges into a free surface, significant air is entrained into the water and forms air pockets. These air pockets eventually break up into small bubbles, which travel downstream to form a bubbly wake. To better understand…