Related papers: Diode laser welding of ABS: Experiments and proces…
In order to predict the more accurate shape information of the melt pool in Selective Laser Melting (SLM), a new finite element temperature field simulations model is proposed. The simulations use a new heat source model that takes into…
The tuning of fused filament fabrication parameters is notoriously challenging. We propose an autonomous data-driven method to select parameters based on in situ measurements. We use a laser sensor to evaluate the surface roughness of a…
We explore, theoretically and experimentally, a method for cooling a broadband heat reservoir, via its laser-assisted collisions with two-level atoms followed by their fluorescence. This method is shown to be advantageous compared to…
We present methods and results of the testing of an inexpensive home-made diffraction limited lens system, the design of which was proposed in a recent paper and which has since been used (with slight alterations) by several research…
We present mechanical measurements performed at low temperatures on cantilever-based microelectro-mechanicalstructures(MEMS) coated with a metallic layer. Two very different coatings are presented in order to illustrate the capabilities of…
Sintering, as a thermal process at elevated temperature below the melting point, is widely used to bond contacting particles into engineering products such as ceramics, metals, polymers, and cemented carbides. Modelling and simulation as…
This study presents the spreading of a single filament of a yield stress (viscoplastic) fluid extruded onto a pre-wetted solid surface. The filaments spread laterally under surface tension forces until they reach a final equilibrium shape…
We present an approach for state and parameter estimation in retinal laser treatment by a novel setup where both measurement and heating is performed by a single laser. In this medical application, the temperature that is induced by the…
Ultrafast laser heating of electrons on a metal surface breaks the pressure equilibrium within the material, thus initiating ablation. The stasis of a room-temperature metal results from a balance between repulsive and attractive binding…
Explicit expressions, for efficient application in engineering practice, are derived for generalized displacements and stresses in simply supported multi-layered wide plates and beams subjected to steady-state thermal and mechanical…
An extremely sensitive temperature measurement MEMS device is developed based on the principle of structural deflection in a bi-material cantilever caused by a difference in thermal expansion coefficients. A dual-beam asymmetrical geometry…
The Subarcsecond Telescope And BaLloon Experiment, STABLE, is the fine stage of a guidance system for a high-altitude ballooning platform designed to demonstrate subarcsecond pointing stability, over one minute using relatively dim guide…
This survey presents a literature review on friction stir welding (FSW) modeling with a special focus on the heat generation due to the contact conditions between the FSW tool and the workpiece. The physical process is described and the…
We propose a model for thermo-elastic beams, consistent with the theory of linear three-dimensional thermo-elasticity and deduced by a suitable version of the Principle of Virtual Powers. Dimensional reduction is achieved by postulating…
As an aid to the development of hydrogen separation membranes, we predict the temperature dependent phase diagrams using first principles calculations combined with thermodynamic principles. Our method models the phase diagram without…
By computer numerical simulation of heating of a dust conducting particle in homogeneous plasma it was shown that depending on initial temperature of a particle both heating and cooling were possible with formation of two different…
A machine-learning non-contact method to determine the temperature of a laser gain medium via its laser emission with a trained few-layer neural net model is presented. The training of the feed-forward Neural Network (NN) enables the…
We present a computational framework for the simulations of powder-bed fusion of metallic alloys, which combines: (1) CalPhaD calculations of temperature-dependent alloy properties and phase diagrams, (2) macroscale finite element (FE)…
Laser Powder Bed Fusion (L-PBF) is a widely adopted additive manufacturing process for fabricating complex metallic parts layer by layer. Effective thermal management is essential to ensure part quality and structural integrity, as thermal…
Since the first proof-of-concept demonstrations of photoluminescence-based optical refrigeration, solid-state laser cooling has developed into a credible competitor to conventional cryogenic technologies. Solid-state laser cooling continues…