Related papers: Instability of a moving contact line
When a contact line (CL) -- where a liquid-vapor interface meets a substrate -- is put into motion, it is well known that the contact angle differs between advancing and receding CLs. Using non-equilibrium molecular dynamics simulations, we…
When a solid plate is withdrawn from a liquid bath, a receding contact line is formed where solid, liquid, and gas meet. Above a critical speed $U_{cr}$, a stationary contact line can no longer exist and the solid will eventually be covered…
A prototypical problem in the study of wetting phenomena is that of a solid plunging into or being withdrawn from a liquid bath. In the latter, de-wetting case, a critical speed exists above which a stationary contact line is no longer…
The dynamics of receding contact lines is investigated experimentally through controlled perturbations of a meniscus in a dip coating experiment. We first characterize stationary menisci and their breakdown at the coating transition. It is…
The flow near a moving contact line depends on the dynamic contact angle, viscosity ratio, and capillary number. We report experiments involving immersing a plate into a liquid bath, concurrently measuring the interface shape, interfacial…
The understanding of the spreading of liquids on solid surfaces is an important challenge for contemporary physics. Today, the motion of the contact line formed at the intersection of two immiscible fluids and a solid is still subject to…
A hydrophilic liquid, such as water, forms hydrogen bonds with a hydrophilic substrate. The strength and locality of the hydrogen bonding interactions prohibit slip of the liquid over the substrate. The question then arises how the contact…
We studied the dynamics of a liquid contact line receding on a hydrophobic soft gel (SBS-paraffin). In order to realize a well-defined geometry with an accurate control of velocity, a dip-coating setup was implemented. Provided that the…
We investigate a possibility to regularize the hydrodynamic contact line singularity in the configuration of partial wetting (liquid wedge on a solid substrate) via evaporation-condensation, when an inert gas is present in the atmosphere…
We investigate experimentally the receding of a contact line when a Peltier module is pulled out of a water bath at constant speed, while a ice layer is also growing at constant speed on the Peltier module. A steady regime is therefore…
The relaxation of a dewetting contact line is investigated theoretically in the so-called "Landau-Levich" geometry in which a vertical solid plate is withdrawn from a bath of partially wetting liquid. The study is performed in the framework…
We report on the onset of fluid entrainment when a contact line is forced to advance over a dry solid of arbitrary wettability. We show that entrainment occurs at a critical advancing speed beyond which the balance between capillary,…
The dynamics of the deformations of a moving contact line is formulated. It is shown that an advancing contact line relaxes more quickly as compared to the equilibium case, while for a receding contact line there is a corresponding slowing…
We study the dynamics of the interface between two immiscible fluids in contact with a chemically homogeneous moving solid plate. We consider the generic case of two fluids with any viscosity ratio and of a plate moving in either directions…
The moving-contact line between a fluid, liquid and a solid is a ubiquitous phenomenon, and determining the maximum speed at which a liquid can wet/dewet a solid is a practically important problem. Using continuum models, previous studies…
The surface of a liquid near a moving contact line is highly curved owing to diverging viscous forces. Thus, microscopic physics must be invoked at the contact line and matched to the hydrodynamic solution farther away. This matching has…
We study the flow close to an advancing contact line in the limit of small capillary number. To take into account wetting effects, both long and short-ranged contributions to the disjoining pressure are taken into account. In front of the…
In part 1, we proposed a model of dynamics of wetting for slow movements near a contact line formed at the interface of two immiscible fluids and a solid when viscous dissipation remains bounded. The contact line is not a material line and…
The movement of the triple contact line plays a crucial role in many applications such as ink-jet printing, liquid coating and drainage (imbibition) in porous media. To design accurate computational tools for these applications, predictive…
Given that contact line between liquid and solid phases can move regardless how negligibly small are the surface roughness, Navier slip, liquid volatility, impurities, deviations from the Newtonian behavior, and other system-dependent…