Related papers: Investigation of Flow Inside an Axial-Flow Pump of…
We report the analysis of radial characteristics of the flow of granular material through a conical hopper. The discharge is simulated for various orifice sizes and hopper opening angles. Velocity profiles are measured along two radial…
In this paper, we present the results of a numerical study of air-water turbulent bubbly flow in a periodic vertical square duct. The study is conducted using a novel numerical technique which leverages Volume of Fluid method for interface…
The flow near a moving contact line depends on the dynamic contact angle, viscosity ratio, and capillary number. We report experiments involving immersing a plate into a liquid bath, concurrently measuring the interface shape, interfacial…
In this paper we study isentropic flow in a curved pipe. We focus on the consequences of the geometry of the pipe on the dynamics of the flow. More precisely, we present the solution of the general Cauchy problem for isentropic fluid flow…
Suspensions of finite-size solid particles in a turbulent pipe flow are found in many industrial and technical flows. Due to the ample parameter space consisting of particle size, concentration, density and Reynolds number, a complete…
Cyclic-to-cycle variability, CCV, of intake-jet flow in an optical engine was measured using particle image velocimetry (PIV), revealing the possibility of two different flow patterns. A phase-dependent proper orthogonal decomposition (POD)…
Two-dimensional laminar flow of a viscous fluid induced by peristalsis due to a moving wall wave has been studied previously for a rectangular channel, a circular tube, and a concentric circular annulus. Here we study peristaltic flow in a…
A computational fluid dynamics model is used to predict the oscillatory flow through tapered cylindrical tube sections (jet pumps). The asymmetric shape of jet pumps results in a time-averaged pressure drop that can be used to suppress…
Microfluidics involves the manipulation of flows at the microscale, typically requiring external power sources to generate pressure gradients. Alternatively, harnessing flows from active fluids, which are usually chaotic, has been proposed…
We report on Lagrangian flow statistics from experimental measurements of homogeneous isotropic turbulence. The investigated flow is driven by 12 impellers inside an icosahedral volume. Seven impeller rotation rates are considered resulting…
Numerical simulations of the flow in an extrusion damper are performed using a finite volume method. The damper is assumed to consist of a shaft, with or without a spherical bulge, oscillating axially in a containing cylinder filled with a…
We present the first direct numerical simulations of particle-laden turbulent flow in concentric annuli to investigate the effects of transverse curvature over a range of Stokes numbers. The results demonstrate that transverse curvature…
The paper proposes a solution an actual scientific problem related to load balancing and efficient utilization of resources of the distributed system. The proposed method is based on calculation of load CPU, memory, and bandwidth by flows…
Two wire mesh tomography devices and a liquid collector were used to study the influence of the gas flow rate on liquid distribution when fluids distribution on top of the reactor is ensured by a perforated plate. In opposition to most of…
The paper presents issues regarding the flux estimation of induction machines. The electrical machines variables estimation represents a major problem in the actual context of modern control approaches, especially of sensorless control…
Grid turbulence is investigated using cross-correlation digital Particle Image Velocimetry (PIV) over a range of Taylor Reynolds Number (Re{\lambda}) from 5 to 44. Instantaneous velocity is measured directly and vorticity and velocity…
Cross-flow, or vertical-axis, turbines are a promising technology for capturing kinetic energy in wind or flowing water and their inherently unsteady fluid mechanics present unique opportunities for control optimization of individual rotors…
The main aim of this study is to find the best, most rapid, and the most accurate numerical method to find the liquid-gas interface of capillary driven flow during the time in circular Microchannels by using COMSOL Multiphysics software.…
We study the local flow properties of various materials in a vane-in-cup geometry. We use magnetic resonance imaging techniques to measure velocities and particle concentrations in flowing Newtonian fluid, yield stress fluid, and in a…
We examine transient axial creeping flow in the annular gap between a rigid cylinder and a concentric elastic tube. The gap is initially filled with a thin fluid layer. The study focuses on viscous-elastic time-scales for which the rate of…