Related papers: Hydrodynamic theory of de-wetting
We study the dewetting of a porous plate withdrawn from a bath of fluid. The microscopic contact angle is fixed to zero and the flow is assumed to be parallel to the plate (lubrication approximation). The ordinary differential equation…
A partially miscible binary liquid mixture, composed of A and B particles, is considered theoretically under conditions for which a stable A-rich liquid phase is in thermal equilibrium with the vapor phase. The B-rich liquid is metastable.…
The dip-coating geometry, where a solid plate is withdrawn from or plunged into a liquid pool, offers a prototypical example of wetting flows involving contact-line motion. Such flows are commonly studied using the lubrication approximation…
Four on-lattice and six off-lattice models for active matter are studied numerically, showing that in contact with a wall, they display universal wetting transitions between three distinctive phases. The particles, which interact via…
Wetting transitions have been predicted and observed to occur for various combinations of fluids and surfaces. This paper describes the origin of such transitions, for liquid films on solid surfaces, in terms of the gas-surface interaction…
Liquid-liquid wetting failure is investigated in a two-dimensional Couette system with two immiscible fluids of arbitrary viscosity. The problem is solved exactly using a sharp interface treatment of hydrodynamics (lubrication theory) as a…
Liquid water can become metastable with respect to its vapor in hydrophobic confinement. The resulting dewetting transitions are often impeded by large kinetic barriers. According to macroscopic theory, such barriers arise from the free…
The spreading of a pure, volatile liquid on a wettable substrate has been studied in extensive detail. Here we show that the addition of a miscible, non-volatile liquid can strongly alter the contact line dynamics and the final liquid…
Flow of a thin viscous film down a flat inclined plane becomes unstable to long wave interfacial fluctuations when the Reynolds number based on the mean film thickness becomes larger than a critical value (this value decreases as the angle…
Above a critical temperature known as the Leidenfrost point (LFP), a heated surface can suspend a liquid droplet above a film of its own vapor. The insulating vapor film can be highly detrimental in metallurgical quenching and thermal…
When a liquid film lies on a non-wettable substrate, the configuration is unstable and the film then retracts from a solid substrate to form droplets. This phenomenon, known as dewetting, commonly leads to undesirable morphological changes.…
Drying suspensions often leave behind complex patterns of particulates, as might be seen in the coffee stains on a table. Here we consider the dynamics of periodic band or uniform solid film formation on a vertical plate suspended partially…
Substrate defects crucially influence the onset of sliding drop motion under lateral driving. A finite force is necessary to overcome the pinning influence even of microscale heterogeneities. The depinning dynamics of three-dimensional…
We studied the dynamics of a liquid contact line receding on a hydrophobic soft gel (SBS-paraffin). In order to realize a well-defined geometry with an accurate control of velocity, a dip-coating setup was implemented. Provided that the…
Switchable and adaptive substrates emerged as valuable tools for the control of wetting and actuation of droplet motion. Here we report a computational study of the dynamics of an unstable thin liquid film deposited on a switchable…
Many features of real granular fluids under rapid flow are exhibited as well by a system of smooth hard spheres with inelastic collisions. For such a system, it is tempting to apply standard methods of kinetic theory and hydrodynamics to…
The dynamics of the wetting front are considered during the imbibition of a fluid into a porous substrate through a circular drawing area. A mathematical model of this process, assuming incompressible Darcy flow, is presented, before the…
The entrainment of air by advancing contact lines is studied by plunging a solid plate into a very viscous liquid. Above a threshold velocity, we observe the formation of an extended air film, typically 10 microns thick, which subsequently…
When a droplet is brought in contact with an undercooled surface, it wets the substrate and solidifies at the same time. The interplay between the phase transition effects and the contact-line motion, leading to its arrest, remains poorly…
Wetting flows are controlled by the contact line motion. We derive an equation that describes the slow time evolution of the triple solid-liquid-fluid contact line for an arbitrary distribution of defects on a solid surface. The capillary…