Related papers: Configuration of the ATLAS Trigger System
The ATLAS High Level Trigger (HLT) consists of two selection steps: the second level trigger and the event filter. Both will be implemented in software, running on mostly commodity hardware. Both levels have a coherent approach to event…
With the high bunch-crossing and interaction rates and potentially large event sizes the experiments at the LHC challenge data acquisition and trigger systems. Within the ATLAS experiment, a multi-level trigger system based on hardware and…
Among the many challenges presented by the future ATLAS detector at the LHC are the high data taking rate and volume and the derivation of a rapid trigger decision with limited resources. To address this challenge within the ATLAS second…
The ATLAS High Level Trigger (HLT) system provides software-based event selection after the initial LVL1 hardware trigger. It is composed of two stages, the LVL2 trigger and the Event Filter. The HLT is implemented as software tasks running…
The ATLAS detector at CERN's Large Hadron Collider will be exposed to proton-proton collisions from beams crossing at 40 MHz that have to be reduced to the few 100 Hz allowed by the storage systems. A three-level trigger system has been…
The CMS experiment has been designed with a 2-level trigger system: the Level 1 Trigger, implemented on custom-designed electronics, and the High Level Trigger (HLT), a streamlined version of the CMS offline reconstruction software running…
The ATLAS trigger has been used very successfully for the online event selection during the first part of the second LHC run (Run-2) in 2015/16 at a center-of-mass energy of 13 TeV. The trigger system is composed of a hardware Level-1…
The trigger selection capabilities of the ATLAS detector have been significantly enhanced for the LHC Run- 2 in order to cope with the higher event rates and with the large number of simultaneous interactions (pile-up) per protonproton…
The ATLAS trigger system is based on three levels of event selection that select the physics of interest from an initial bunch-crossing rate of 40 MHz. During nominal LHC operations at a luminosity of 10^34 cm^-2 s^-1, decisions must be…
After the current shutdown, the LHC is about to resume operation for a new data-taking period, when it will operate with increased luminosity, event rate and center of mass energy. The new conditions will impose more demanding constraints…
Given the extremely high output rate foreseen at LHC and the general-purpose nature of ATLAS experiment, an efficient and flexible way to select events in the High Level Trigger is needed. An extremely flexible solution is proposed that…
During LHC Run 2 (2015-2018) the ATLAS Level-1 topological trigger allowed efficient data-taking by the ATLAS experiment at luminosities up to 2.1x10$^{34}$ cm$^{-2}$s$^{-1}$, which exceeds the design value by a factor of two. The system…
The upgrade to the ATLAS trigger for LHC Run 2 is presented including a description of the design and performance of the newly reimplemented tracking algorithms. The profiling infrastructure, constructed to provide prompt feedback from the…
The ATLAS Trigger system is a key component of the ATLAS experiment at the CERN Large Hadron Collider (LHC), designed to reduce the event rate from the 40 MHz proton-proton bunch crossing frequency to an output suitable for offline storage…
This article describes the design, testing and production of the ATLAS Region of Interest Builder (RoIB). This device acts as an interface between the Level 1 trigger and the high level trigger (HLT) farm for the ATLAS LHC detector. It…
The ATLAS detector at CERN's Large Hadron Collider (LHC) will be exposed to proton-proton collisions from beams crossing at 40 MHz. At the design luminosity of 10^34 cm^-2 s^-1 there are on average 23 collisions per bunch crossing. A…
The ATLAS experiment at the Large Hadron Collider employs a two-level trigger system to record data at an average rate of 1 kHz from physics collisions, starting from an initial bunch crossing rate of 40 MHz. During the LHC Run 2…
The ATLAS detector at CERN's Large Hadron Collider will be exposed to proton-proton collisions from beams crossing at 40 MHz. A three-level trigger system was designed to select potentially interesting events and reduce the incoming rate to…
ATLAS detector at the LHC will undergo a major Phase-II upgrade for the High Luminosity LHC. The upgrade affects all major ATLAS systems, including the Trigger and Data Acquisition systems. As part of the Level-0 Trigger System, the Global…
The CMS experiment has been designed with a two-level trigger system: the Level-1 Trigger, implemented on custom-designed electronics, and the High Level Trigger, a streamlined version of the CMS offline reconstruction software running on a…