Related papers: An Overview of the LIGO Control and Data Acquisiti…

Efficient operation of a submillimeter interferometer requires remote (preferably automated) control of mechanically tuned local oscillators, phase-lock loops, mixers, optics, calibration vanes and cryostats. The present control system for…

The four LHC experiments at CERN have decided to use a commercial SCADA (Supervisory Control And Data Acquisition) product for the supervision of their DCS (Detector Control System). The selected SCADA, which is therefore used for the CMS…

High power in narrow frequency bands, spectral lines, are a feature of an interferometric gravitational wave detector's output. Some lines are coherent between interferometers, in particular, the 2 km and 4 km LIGO Hanford instruments. This…

One of the optimization goals of a particle accelerator is to reach the highest possible beam peak current. For that to happen the electron bunch propagating through the accelerator should be kept relatively short along the direction of its…

MIMO (Multi Input Multi Output) wireless communication system is an innovative solution to improve the bandwidth efficiency by exploiting multipath-richness of the propagation environment. The degree of multipath-richness of the channel…

LIGO interferometer is considered the most sensitive and complicated gravitational experimental equipment ever built. Its main objective is to detect the gravitational wave from the strongest events in the universe by observing if the…

Diffuse correlation spectroscopy (DCS) is a noninvasive optical technique that probes microvascular blood flow in deep tissues. Here, we present and validate a new on-chip hardware correlator for high-speed DCS measurements. The correlator…

EAST (Experimental Advanced Superconducting Tokamak) Technical Diagnostic System (TDS) is used to monitor the outlet temperature of all superconducting coils, in case of temperature anomaly, it will trigger safety interlock system to meet…

In the initial phase of the Swiss Light Source, four insertion devices will be installed. The control system for all the ID's follows an uniform concept to allow a rapid installation schedule, while at the same time allowing for a variety…

The DarkSide-20k (DS-20k) detector is designed to directly search for dark matter by detecting weakly interacting massive particles (WIMPs) scattering off nuclei in a 20 tonnes target of low radioactivity Argon from underground sources, in…

This paper describes the design and development of low cost USB Data Acquisition System (DAS) for the measurement of physical parameters. Physical parameters such as temperature, humidity, light intensity etc., which are generally slowly…

The development of a multiple-channel lock-in optical spectrometer (LIOS) is presented, which enables parallel phase-sensitive detection at the output of an optical spectrometer. The light intensity from a spectrally broad source is…

LIGO, the Laser Interferometer Gravitational-wave Observatory, has been designed and constructed to measure gravitational wave strain via differential arm length. The LIGO 4-km Michelson arms with Fabry-Perot cavities have auxiliary length…

The Front End Driver, FED, is a 9U 400mm VME64x card designed for reading out the Compact Muon Solenoid, CMS, silicon tracker signals transmitted by the APV25 analogue pipeline Application Specific Integrated Circuits. The FED receives the…

The ATLAS detector at CERN's Large Hadron Collider (LHC) is equipped with a tracking system at its core (the Inner Detector, ID) consisting of silicon and gaseous straw tube detectors. The physics performance of the ID requires a precision…

The Laser Interferometer Space Antenna (LISA) is a proposed space mission for the detection of gravitational waves. It consists of three drag-free satellites flying in a triangular constellation. A gravitational reference sensor is used in…

A low-cost, stand-alone Global-Positioning-System-time-synchronized data acquisition system is described. The constructed prototype allows recoding up to four analog signals with a 16-bit resolution in variable ranges and a maximum sampling…

Novel electronic devices can often be operated in a plethora of ways, which makes testing circuits comprised of them difficult. Often, no single tool can simultaneously analyze the operating margins, maximum speed, and failure modes of a…

Closed-loop control systems employ continuous sensing and actuation to maintain controlled variables within preset bounds and achieve the desired system output. Intentional disturbances in the system, such as in the case of cyberattacks,…

Unified Diagnostic Services (UDS) is a diagnostic communication protocol used in electronic control units (ECUs) within automotive electronics, which is specified in the ISO 14229-1. It is derived from ISO 14230-3 (KWP2000) and the now…