Related papers: Energy Stability in a High Intensity Pulsed SC Pro…
In order to dissipate long-lived radioactive waste, not only high ux proton accelerator but also electron linac have been proposed. A proton accelerator directly induces nuclear fission and mutation. On the other hand, electron beam has two…
Three alternative designs of the European Spallation Source (ESS) high energy linac are described. The most promising ones are either a normalconducting (nc) coupled cavity linac (CCL) up tofinal energy or a change at 407 MeV to only one…
The conception of High Power Linac developed in Russian accelerator centres is based on the use of independently phased SC resonators with quadrupole lenses between them. The type and parameters of the resonators as well as focusing…
The superconducting (SC) proton linac is proposed in the JAERI/KEK Joint Project for a high-intensity proton accelerator in the energy region from 400 to 600 MeV. Highly stable fields in the SC cavities are required under the dynamic…
The CLIC linear collider aims at accelerating multiple bunches of electrons and positrons and colliding them at a centre of mass energy of 3 TeV. These bunches will be accelerated through X-band linacs, operating at an accelerating…
The main `bottleneck' limiting the beam power in circular machines is caused by space charge effects that produce beam instabilities. To increase maximally the beam power of a `proton driver', it is proposed to build a facility consisting…
In this paper we present results of using parallel supercomputers to simulate beam dynamics in next-generation high intensity ion linacs. Our approach uses a three-dimensional space charge calculation with six types of boundary conditions.…
A superconducting (SC) linac is expected to lead to outstanding discoveries in various scientific fields because its beam current is a few orders of magnitude larger than in a normal-conducting linac. However, the widespread use of SC linac…
This lecture is an introduction to the design of a spallation neutron source and other high intensity proton sources. It discusses two different approaches: linac-based and synchrotron-based. The requirements and design concepts of each…
The peak current limit for the Fermilab Linac was recently studied. The purpose was to learn what components of the present Linac can be used for the first stage of a proposed proton driver[1]. For this application the Linac must provide a…
The SNS linac accelerates an average beam current of 2 mA to an energy of 968 MeV. The linac is pulsed at 60 Hz with an H- beam pulse of 1 ms. The first 185 Mev of the linac uses normal conducting cavities, and the remaining length of the…
A proposal for a 10-120 mA proton linac employing superconducting beta-graded, CERN type, four cell cavities at 352 MHz is presented. The high energy part (100 MeV-1 GeV) of the machine is split in three beta-graded sections, and transverse…
The Pohang Accelerator Laboratory operates an electron linac for the pulsed neutron source as one of the long-term nuclear R&D programs at the Korea Atomic Energy Research Institute. The designed beam parameters are as follows; The nominal…
Injected beam energy and energy spread are critical parameters affecting the performance of our rapid cycling synchrotron (RCS). A real-time energy monitoring system is being installed to examine the H- beam out of the Intense Pulsed…
The continue wave (CW) high current proton linac has wide applications as the front end of the high power proton machines. The low energy part is the most difficult one and there is no widely accepted solution yet. Both normal conducting…
High-frequency hadron-therapy linacs have been studied for the last 20 years and are now being built for dedicated proton-therapy centres. The main reason for using high-frequency linacs, in spite of the small apertures and low-duty cycle,…
Beam loss is a critical issue in high-intensity accelerators, and much effort is expended during both the design and operation phases to minimize the loss and to keep it to manageable levels. As new accelerators become ever more powerful,…
The 1.7-GeV 100-mA CW proton linac is now under design for the Accelerator Production of Tritium (APT) Project. The APT linac comprises both the normal conducting (below 211 MeV) and superconducting (SC) sections. The high current leads to…
Slow positrons are increasingly important to the study of material surfaces. For these kinds of studies, the positrons must have low emittance and relatively high brightness. Unfortunately, fast positron sources like radioactive capsules or…
The JAERI/KEK Joint Project for the high-intensity proton accelerator facility has been proposed with a superconducting (SC) linac option from 400 MeV to 600MeV. System design of the SC linac has been carried out based on the…