Related papers: Pulsed Neutron Source using 100-MeV electron Linac…
The Long Baseline Neutrino Facility (LBNF) will produce the worlds most intense neutrino beam. Three series connected magnetic horns will require 5kV, 300kA, 800$\mu$s pulses at a rate of 0.7Hz to focus the beam. Fermilab has designed and…
We report on the development of a radio frequency (RF) linear accelerator (linac) for multiple-ion beams that is made from stacks of low cost wafers. The accelerator lattice is comprised of RF-acceleration gaps and electrostatic quadrupole…
A pulsed electron gun that can produce MHz repetition rate nanosecond pulses is described. The gun uses a Pierce grid in combination with an anode to extract electrons from a tungsten filament cathode. The electrons emerging from the anode…
To produce the intense, high-quality hadron beams required by future nuclear and high-energy physics experiments, synchrotrons need to overcome a most prominent intensity limitation i.e., space charge. This Letter characterizes the…
For the CLIC two-beam scheme, a high-current, long-pulse drive beam is required for RF power generation. Taking advantage of the 3 GHz klystrons available at the LEP injector once LEP stops, a 180 MeV electron accelerator is being…
A light emitting diode (LED) pulser has been developed that can be used for tests or calibration of timing and amplitude sensitivity of particle physics detectors. A comparative study is performed on the components and pulser output…
The CLIC linear collider aims at accelerating multiple bunches of electrons and positrons and colliding them at a centre of mass energy of 3 TeV. These bunches will be accelerated through X-band linacs, operating at an accelerating…
This paper describes a design for the front end of a superconducting (SC) ion linac which can accept and simultaneously accelerate two charge states of uranium from an ECR ion source. This mode of operation increases the beam current…
Configuring clinical linear accelerators (linacs) for ultra-high dose rate (UHDR) electron experiments typically requires invasive hardware manipulation and/or irreversible manufacturer modifications, limiting broader implementation. We…
Implementation and commissioning of the EPICS based control system for the ISAC radioactive beam facility was completed. The target ion source, mass separator, and low-energy beam-lines started beam production for experiments. In parallel,…
High-Current Accelerator-driven Neutron Sources (HiCANS) are currently under development across Europe to address the shortage of medium-scale neutron sources, as many research nuclear reactors have been decommissioned over the past several…
Two pulsed power systems have been upgraded for the g-2 experiment at Fermilab. The Pbar Lithium Lens supply previously ran with a half sine pulsed current of 75 kA peak, 400 us duration and a repetition rate of 0.45 pps. For the g-2…
The continue wave (CW) high current proton linac has wide applications as the front end of the high power proton machines. The low energy part is the most difficult one and there is no widely accepted solution yet. Based on the analysis of…
The readout electronics of the ATLAS Hadronic Endcap Calorimeter will have to withstand the about ten times larger radiation environment of the future high-luminosity LHC (HL-LHC) compared to their design values. The GaAs ASIC which…
An "ultimate" high intensity proton source for neutrino factories and/or muon colliders was projected to be a ~4 MW multi-GeV proton source providing short, intense proton pulses at ~15 Hz. The JPARC ~1 MW accelerators provide beam at…
The Source Development Lab (SDL) at BNL consists of a 230 MeV electron linac and a 10 m long wiggler for short wavelength Free Electronic Laser (FEL) development. The original control system [1] was based on the one in use at the National…
Laser-accelerated electron beams have been created at a kHz repetition rate from the {\it reflection} of intense ($\sim10^{18}$ W/cm$^2$), $\sim$40 fs laser pulses focused on a continuous water-jet in an experiment at the Air Force Research…
The Linear Accelerator 4 (LINAC 4) is designed to accelerate negative hydrogen ions to high energies for injection into the Large Hadron Collider (LHC), where it has been supplying proton beams since 2020. LINAC 4 accelerates negative…
A compact high repetition rate attosecond light source based on a standard laser oscillator combined with plasmonic enhancement is presented. At repetition rates of tens of MHz, we predict focusable pulses with durations of ~< 300…
The Fusion Prototypic Neutron Source (FPNS) is considered to be a testbed for scientific understanding of material degradation in future nuclear fusion reactors [1-3]. The primary mission of FPNS is to provide a damage rate in iron samples…