Related papers: A Superconductive, Low Beta Single Gap Cavity for …

The superconducting circuit community has recently discovered the promising potential of superinductors. These circuit elements have a characteristic impedance exceeding the resistance quantum $R_\text{Q} \approx 6.45~\text{k}\Omega$ which…

Superconducting cavities with low RF frequencies and heavy damping of higher order modes (HOM) are desired for the main accelerator of High Energy Photon Source (HEPS), a 6 GeV synchrotron light source promising ultralow emittance currently…

The Proton Improvement Plan-II (PIP-II) is a superconducting linear accelerator being built at Fermilab that will provide 800 MeV proton beam for neutrino production. The linac consists of a total of twenty-three (23) cryomodules of five…

This paper presents non-destructive dark current measurements of superconducting TESLA cavities for superconducting LINACs. The measurements were carried out in a highly disturbed accelerator environment using a low temperature…

The high energy beam transport (HEBT) line for the ISAC radioactive beam facility at TRIUMF requires an 11.8 MHz buncher. The main requirements of the buncher are to operate in cw mode with a velocity acceptance of 2.2% and an effective…

A room temperature heavy ion linac has been proposed as a new injector of CSRm (the main Cooler Storage Ring) at HIRFL (Heavy Ion Research Facility in Lanzhou), which is expected to improve the performance of HIRFL. The linac injector can…

The 75-keV injector and 6.7-MeV RFQ that comprise the first portion of the cw, 100-mA proton linac for the accelerator production of tritium (APT) project have been built and operated. The LEDA RFQ has been extensively tested for pulsed and…

Superconducting technology makes it possible to build a high energy $e^+e^-$ linear collider with energy recovery (ERLC) and reusable beams. To avoid parasitic collisions inside the linacs, a twin (dual) LC is proposed. In this article, I…

The upcoming Proton Improvement Plan-II (PIP-II), designated for enhancements to the Fermilab accelerator complex, features a new 800 MeV superconducting linac and a Beam Transfer Line (BTL) to transport the beam to the existing Booster…

We have fabricated superconducting microwave resonators in a lumped element geometry using single crystal silicon dielectric parallel plate capacitors with C >2 pF. Aluminum devices with resonant frequencies between 4.0 and 6.5 GHz…

In this paper we present alternative approach for Future Circular electron-positron Collider. Current 100 km circumference design with the top CM energy of 365 GeV (182.5 GeV beam energy) is based on two storage rings to circulate colliding…

Reentrant cavities are microwave resonant devices employed in a number of different areas of physics. They are appealing due to their simple frequency tuning mechanism, which offers large tuning ranges. Reentrant cavities are, in essence,…

Low-loss microwave components are used in many superconducting resonant circuits from multiplexed readouts of low-temperature detector arrays to quantum bits. Two-level system defects in amorphous dielectric materials cause excess energy…

The Proton Improvement Plan-II (PIP-II, [1]) linac will include 35 Single Spoke Resonators type 2 (SSR2). A total of eight pre-production SSR2 jacketed cavities will be procured and five installed in the first pre-production cryomodule. The…

The design of the proposed linear collider TESLA is based on 9-cell 1.3 GHz superconducting niobium cavities, operated in pulsed mode. Within the framework of an international collaboration the TESLA Test Facility (TTF) has been set up at…

A new linac using superconducting quarter-wave resonators (QWR) is under construction at CERN in the framework of the HIE-ISOLDE project. The QWRs are made of niobium sputtered on a bulk copper substrate. The working frequency at 4.5 K is…

A new bunch length measurement method based on high order mode cavity was proposed. Operating the harmonic cavity at mode TM0n0 so that its radius could be chosen, in order to break the limitation of beam pipe radius. A two-cavity bunch…

This paper outlines the RF design of the CLIC (Compact Linear Collider) 30 GHz main linac accelerating structure and gives the resulting longitudinal and transverse mode properties. The critical requirement for multibunch operation, that…

We present a detailed study of the six-dimensional phase space of the electron beam produced by the Cornell Energy Recovery Linac Photoinjector, a high-brightness, high repetition rate (1.3 GHz) DC photoemission source designed to drive a…

As part of a National Cancer Institute contract to develop a compact source of monoenergetic X-rays via Compton backscattering, we have completed the design and construction of a 5.5 cell Photoinjector operating at 11.424 GHz. Successful…