Related papers: Ultra narrow AuPd and Al wires
We describe a method for fabrication of uniform aluminum nanowires with diameters below 15 nm. Electron beam lithography is used to define narrow wires, which are then etched using a sodium bicarbonate solution, while their resistance is…
We have carried out first principles electronic structure and total energy calculations for a series of ultrathin aluminum nanowires, based on structures obtained by relaxing the model wires of Gulseren et al. The number of conducting…
The performance and cost of Bi-2212/Ag wire is limited by the large fraction of silver matrix (~3:1) that is required in the oxide-powder-in-tube fabrication process. An alternative fabrication process is being developed in which…
Continuous Nb wires, 7-15 nm in diameter, have been fabricated by sputter-coating single fluorinated carbon nanotubes. Transmission electron microscopy revealed that the wires are polycrystalline, having grain sizes of about 5 nm. The…
MgB2 hollow wires have been produced with a new technique which uses a conventional wire manufacturing process but is applied to composite billets containing the elemental B and Mg precursors in an appropriate shape. The technique has been…
Below a certain temperature Tc (typically cryogenic), some materials lose their electric resistance R entering a superconducting state. Folowing the general trend toward a large scale integration of a greater number of electronic…
Conventional electron beam lithography has been used to fabricate mesoscopic Nb wires with a superconducting transition temperature above 7.0 K. The typical line width and the thickness were 200 nm and 45 nm respectively. Nb was deposited…
We report a detailed magnetic study of a new type of self-organized nanowires disclosed briefly previously [B. Borca et al., Appl. Phys. Lett. 90, 142507 (2007)]. The templates, prepared on sapphire wafers in a kinetically-limited regime,…
The stability and electronic structure of a single monatomic Al wire has been studied using the ab initio pseudopotential method. The Al wire undergoes two structural rearrangements under compression, i.e., zigzag configurations at angles…
The localization lengths of ultrathin disordered Au and Ag nanowires are estimated by calculating the wire conductances as functions of wire lengths. We study Ag and Au monoatomic linear chains, and thicker Ag wires with very small cross…
The authors introduce a geometry for ultrathin Au and Ag wires that ab initio calculations indicate to be more stable than previously considered planar geometries for these systems, by about 0.1 eV per atom. This structure is insulating for…
The Short-Baseline Near Detector time projection chamber is unique in the design of its charge readout planes. These anode plane assemblies (APAs) have been fabricated and assembled to meet strict accuracy and precision requirements: wire…
We demonstrate an ultra-compact waveguide taper in Silicon Nitride platform. The proposed taper provides a coupling-efficiency of 95% at a length of 19.5 um in comparison to the standard linear taper of length 50 um that connects a 10 um…
In this paper the concept and the first successful tests towards constructing a superconductive micro-undulator with a period length of 3.8 mm are described. The structures were built with a commercially available NbTi wire. A full 100…
We have studied the thermal properties of atom chips consisting o high thermal conductivity Aluminum Nitride (AlN) substrates on which gold microwires are directly deposited. We have measured the heating of wires of several widths and with…
During the last years several attempts were undertaken to decrease the period length of undulators to the mm range. In this paper, a novel type of an in-vacuum undulator is described which is built with superconductive wires. The period…
We first present a theory of the smallest diameter and then use the theory to guide the experimental realization of Cu nanorods of ~20 nm in diameter and Au nanorods of ~10 nm in diameter, the smallest well-separated metallic nanorods ever…
Neutral atoms can be trapped and manipulated with surface mounted microscopic current carrying and charged structures. We present a lithographic fabrication process for such atom chips based on evaporated metal films. The size limit of this…
Niobium thin film wires were fabricated using electron beam lithography with a four layer liftoff mask system, and subsequently thinned by anodisation. The resistance along the wire was monitored in situ and trimmed by controlling the…
We report on the fabrication and electrical characterization of field-effect devices based on wire-shaped InP crystals grown from Au catalyst particles by a vapor-liquid-solid process. Our InP wires are n-type doped with diameters in the…