Related papers: Stability Limit for Mode-I Fracture
This study presents the formulation, the numerical solution, and the validation of a theoretical framework based on the concept of variable-order mechanics and capable of modeling dynamic fracture in brittle and quasi-brittle solids. More…
The paper addresses the problem of a Mode III interfacial crack advancing quasi-statically in a heterogeneous composite material, that is a two-phase material containing elastic inclusions, both soft and stiff, and defects, such as…
Highly-deformable materials, from synthetic hydrogels to biological tissues, are becoming increasingly important from both fundamental and practical perspectives. Their mechanical behaviors, in particular the dynamics of crack propagation…
A numerical realization of an elastic beam lattice is used to obtain scaling exponents relevant to the extent of damage within the controlled, catastrophic and total regimes of mode-I brittle fracture. The relative fraction of damage at the…
Crack initiation and propagation are fundamental problems in materials science, often leading to catastrophic failure. While fracture in elastic solids occurs instantaneously above a critical load, viscoelastic materials may sustain high…
We numerically investigate the athermal creep deformation of amorphous materials having a wide range of stability. The imposed shear stress serves as the control parameter, allowing us to examine the time-dependent transient response…
Fracture growth in a material is strongly influenced by the presence of inhomogeneities, which deviate crack trajectories from rectilinearity and deeply affect failure. Increasing crack tortuosity is connected to enhancement of fracture…
Within the continuum dislocation theory the asymptotic analysis of the plane strain crack problem for a single crystal having only one active slip system on each half-plane is provided. The results of this asymptotic analysis show that the…
A Particle Tracking Velocimetry experiment has been performed in a turbulent flow at intermediate Reynolds number. We present experimentally obtained stretching rates for particle pairs in the inertial range. When compensated by a…
A novel investigation of the nature of intermittency in incompressible, homogeneous and isotropic turbulence is performed by a numerical study of the Navier-Stokes equations constrained on a fractal Fourier set. The robustness of the energy…
This paper concerns the analysis and implementation of a novel iterative staggered scheme for quasi-static brittle fracture propagation models, where the fracture evolution is tracked by a phase field variable. The model we consider is a…
We perform a detailed theoretical study of the edge fracture instability, which commonly destabilises the fluid-air interface during strong shear flows of entangled polymeric fluids, leading to unreliable rheological measurements. By means…
We extend the linear analysis of the drag instability in a 1D perpendicular isothermal C-shock by Gu & Chen to 2D perpendicular and oblique C-shocks in the typical environment of star-forming clouds. Simplified dispersion relations are…
An asymptotic interface equation for directional solidification near the absolute stabiliy limit is extended by a nonlocal term describing a shear flow parallel to the interface. In the long-wave limit considered, the flow acts…
This study investigates one of the central problems of dynamic fracture mechanics, namely the dependence of the instantaneous stress intensity factor (SIF) on the crack propagation velocity. For this purpose, the well-known experiments by…
The method of iterated conformal maps is developed for quasi-static fracture of brittle materials, for all modes of fracture. Previous theory, that was relevant for mode III only, is extended here to mode I and II. The latter require…
Shear strain localization into shear bands is associated with velocity weakening instabilities and earthquakes. Here, we simulate steady-state plane-shear flow of numerical granular material (gouge), confined between parallel surfaces. Both…
Traditional computational approaches in simulating crack propagation in perfectly brittle materials rely on the estimate of stress intensity factors along the rupture front. This proves highly challenging in 3D when the crack geometry…
Fracture toughness is the material property characterizing resistance to failure. Predicting its value from the solid structure at the atomistic scale remains elusive, even in the simplest situations of brittle fracture. We report here…
The problem of crack pattern formation due to thermal shock loading at the surface of half-space is solved numerically using two-dimensional boundary element method. The results of numerical simulations with 100-200 random simultaneously…