Related papers: Precipitation induced recrystallisation (PIX) in a…
The combined strengthening effects of grain refinement and high precipitated volume fraction (~6at.%) on the mechanical properties of FeSiTi alloy subjected to SPD processing prior to aging treatment were investigated by atom probe…
While lean Mg-Zn-Ca alloys are promising materials for temporary implants, questions remain on the impact of Zn and Ca. In this context, the precipitation in Mg-1.5Zn-0.25Ca (ZX20, in wt.%) was investigated upon linear heating from about…
We consider the process of precipitation in binary alloys in the presence of mechanical deformation. It is commonly observed that mechanical deformation prior to or during precipitation leads to microstructure with excess defects, which…
This work demonstrates the development of a strong and ductile medium entropy alloy by employing conventional alloying and thermomechanical processing to induce partial recrystallization (PR) and precipitation strengthening in the…
Precipitation-strengthened alloys, such as Ni-base, Co-base and Fe-base superalloys, show the development of dendrite-like precipitates in the solid state during aging at near-$\gamma^{\prime}$ solvus temperatures. These features arise out…
A detailed study has been carried out on $\gamma^\prime$ (AlAg$_2$) precipitates in Al-Ag and Al-Ag-Cu alloys to reconcile the conflicting reports on chemical ordering and stacking faults in this phase. High angle annular dark field…
Reduced activation ferritic/martensitic (RAFM) steels are the leading candidate structural materials for first-wall and blanket components in fusion reactors. This work is the first in a series to provide a systematic roadmap of MX…
Elevated pressures are encountered in many metal forming processes that can alter microstructural evolution rates. Here we measure rate changes with pressure in recrystallization and grain growth in Fe through adaptation of…
The tensile creep performance of a polycrystalline Co/Ni-base superalloy with a multimodal gamma prime distribution has been examined at 800C and 300MPa. The rupture life of the alloy is comparable to that of RR1000 tested under similar…
The effect of pre-ageing deformation on the size and distribution of beta-prime precipitates and subsequently on the resulting strength and ductility have been measured in a Mg-3.0at.%Zn-0.5at.%Y alloy. The alloy was extruded and then…
An ultrafine grained magnesium alloy has been produced through room temperature high-pressure torsion (HPT) of solutionised Mg-1.35 wt.%Mn. Dynamic precipitation of nanometer-scale Mn particles occurred during deformation. These particles…
Precipitates are main microstructural features to provide high temperature creep strength and radiation resistance in structural materials for fusion energy systems. However, the mechanisms of precipitate stability under irradiation in…
Nucleation and growth of Ti$_3$Al \textalpha{}$_2$ ordered domains in \textalpha{}-Ti--Al--X alloys were characterised using a combination of transmission electron microscopy, atom probe tomography and small angle X-ray scattering. Model…
The excellent mechanical properties of the Ni-based superalloy IN718 mainly result from coherent $\gamma''$ precipitates. Due to a strongly anisotropic lattice misfit between the matrix and the precipitate phase, the particles exhibit…
We consider the stability of precipitates formed at grain boundaries (GBs) by radiation-induced segregation in dilute alloys subjected to irradiation. The effects of grain size and misorientation of symmetric-tilt GBs are quantified using…
In novel Co and CoNi based superalloys, the creep resistance is limited at high temperatures due to low lattice misfit and solvus temperature. In this study, we combined the advantages of Co-Ti (high lattice misfit and solvus temperature)…
The ultrafast structural response of a thin iron film to sub-ps pulsed laser-induced heating has been investigated using time-resolved X-ray diffraction in the partial melting regime. A tetragonal distortion of the bcc-phase emerges at ~6…
In this paper, we study the effects of $\theta ^\prime$-Al$_2$Cu plate-like precipitates on the plasticity of Al-Cu micro-pillars, with a sample size allowing the precipitates to cross the entire micro-pillar. {100}-slip traces are…
The Fe-Cu system has attracted much attention over the last several decades due to its technological importance as a model alloy for Cu steels. In spite of these efforts several aspects of its phase diagram remain unexplained. Here we use…
Microbial-Induced Carbonate Precipitation (MICP) is an innovative ground improvement technique which can enhance the strength and stiffness of soils, and can also control their hydraulic conductivity. These engineering properties of…