Related papers: Frequency-Adaptive Multi-Band Architecture for Upp…

Multiple-input multiple-output (MIMO) system has been the defining mobile communications technology in recent generations. With the ever-increasing demands looming towards the sixth generation (6G), we are in need of additional degrees of…

The upcoming 3GPP global mobile communication standard 6G strives to push the technological limits of radio frequency (RF) communication even further than its predecessors: Sum data rates beyond 100 Gbit/s, RF bandwidths above 1 GHz per…

The fifth generation (5G) of mobile communications relies on extremely high data transmission rates utilizing a wide range of frequency bands, including FR1 (sub-6 GHz) and FR2 (mmWave). Future mobile communications systems are envisaged to…

High data rates are one of the most prevalent requirements in current mobile communications. To cover this and other high standards regarding performance, increasing coverage, capacity, and reliability, numerous works have proposed the…

This paper considers channel estimation and uplink achievable rate of the coarsely quantized massive multiple-input multiple-output (MIMO) system with radio frequency (RF) impairments. We utilize additive quantization noise model (AQNM) and…

Hybrid analog/digital architectures and receivers with low-resolution analog-to-digital converters (ADCs) are two low power solutions for wireless systems with large antenna arrays. Most prior work represents two extreme cases in which…

Large antenna arrays will be needed in future millimeter wave (mmWave) cellular networks, enabling a large number of different possible antenna architectures and multiple-input multiple-output (MIMO) techniques. It is still unclear which…

The increasing demand for wireless connectivity necessitates advanced spectrum modeling to enable efficient spectrum sharing for next-generation aerial communications. While traditional models often overlook vertical variations in signal…

Future wireless multiple-input multiple-output (MIMO) communication systems will employ sub-6 GHz and millimeter wave (mmWave) frequency bands working cooperatively. Establishing a MIMO communication link usually relies on estimating…

Sixth-generation (6G) networks are envisioned to achieve full-band cognition by jointly utilizing spectrum resources from Frequency Range 1 (FR1) to Frequency Range 3 (FR3, 7-24 GHz). Realizing this vision faces two challenges. First,…

The high hardware complexity of a massive MIMO base station, which requires hundreds of radio chains, makes it challenging to build commercially. One way to reduce the hardware complexity and power consumption of the receiver is to lower…

Designing and developing a millimetre-wave(mmWave) based mobile Radio Access Technology (RAT) in the 6-100 GHz frequency range is a fundamental component in the standardization of the new 5G radio interface, recently kicked off by 3GPP.…

The fundamental limits of communication over multiple-input multiple-output (MIMO) networks are considered when a limited number of one-bit analog to digital converters (ADC) are used at the receiver terminals. Prior works have mainly…

At millimeter wave (mmWave) frequencies, the higher cost and power consumption of hardware components in multiple-input multiple output (MIMO) systems do not allow beamforming entirely at the baseband with a separate radio frequency (RF)…

Reconfigurable antennas possess the capability to dynamically adjust their fundamental operating characteristics, thereby enhancing system adaptability and performance. To fully exploit this flexibility in modern wireless communication…

Reconfigurable intelligent surface (RIS) has emerged as a cost-effective solution for green communications in 6G. However, its further extensive use has been greatly limited due to its fully passive characteristics. Considering the…

Cellular wireless systems are facing a proliferation of frequency bands over a wide spectrum, particularly with the expansion into FR3. These bands must be supported in user equipment (UE) handsets with multiple antennas in a constrained…

The large bandwidths available at millimeter wave (mmWave) FR2 bands (24-71 GHz) and the emerging FR3 bands (7-24 GHz) are essential for supporting high data rates. Highly directional beams utilized to overcome the attenuation in these…

Motivated by the demand for energy-efficient communication solutions in the next generation cellular network, a mixed-ADC receiver architecture for massive multiple input multiple output (MIMO) systems is proposed, which differs from…

Application of massive multiple-input multiple-output (MIMO) systems to frequency division duplex (FDD) is challenging mainly due to the considerable overhead required for downlink training and feedback. Channel extrapolation, i.e.,…