Related papers: Precipitate size evolution in an ultrafine-grained…
An ultrafine grained magnesium alloy has been produced through room temperature high-pressure torsion (HPT) of solutionised Mg-1.35 wt.%Mn. Dynamic precipitation of nanometer-scale Mn particles occurred during deformation. These particles…
Microstructural analysis of a Mg-Zn alloy deformed at room temperature by high-pressure torsion (HPT) indicates that fine-scale precipitation occurs even without post-deformation heat treatment. Small-angle X-ray scattering detects…
We report on a quantitative investigation into the effect of size and distribution of rod-shaped \beta' precipitates on strength and ductility of a Mg-Zn alloy. Despite precipitation strengthening being crucial for the practical application…
The effect of pre-ageing deformation on the size and distribution of beta-prime precipitates and subsequently on the resulting strength and ductility have been measured in a Mg-3.0at.%Zn-0.5at.%Y alloy. The alloy was extruded and then…
Two different precipitate hardening aluminium alloys processed by friction stir welding were investigated. The microstructure and the hardness of the as delivered materials were compared to that of the weld nugget. Transmission electron…
Bulk single crystals of manganese arsenide (MnAs) were grown from melt at 1 GPa and 1100 {\deg}C by using a cubic-anvil, high-pressure, and high-temperature technique. The as-grown black colored crystals extracted from solidified lump…
While lean Mg-Zn-Ca alloys are promising materials for temporary implants, questions remain on the impact of Zn and Ca. In this context, the precipitation in Mg-1.5Zn-0.25Ca (ZX20, in wt.%) was investigated upon linear heating from about…
The finite-size effect on the evolution of Griffiths phase (GP) is studied using nanoparticles of half-doped manganite Pr$_{0.5}$Sr$_{0.5}$MnO$_{3}$ with different average particle sizes but having similar structural parameters. All the…
A new family of high-strength Al-alloys has recently been developed, tailored for the powder bed fusion-laser beam process. In these alloys, Mn, Cr and Zr are incorporated in solid solution at amounts up to three times that of equilibrium…
Although magnesium alloys deform extensively through shear strains and crystallographic re-orientations associated with the growth of twins, little is known about the strengthening mechanisms associated with this deformation mode. A crystal…
Bulk single crystals of manganese phosphide (MnP) were grown from melt at 1 GPa and 1200 C by using a cubic-anvil, high-pressure, and high-temperature technique. The obtained black colored crystals exhibit a plate-like morphology, with flat…
Magnesium (Mg) and its alloys hold great potential as an energy-saving structural material for automative, aerospace applications. However, the use of Mg alloys has been limited due to poor ductility and formability. Poor mechanical…
MgB2 samples prepared by solid-state reaction were investigated using high-resolution transmission electron microscopy (HREM), X-ray energy-dispersive spectroscopy (EDX), electron energy-loss spectroscopy (EELS), and energy-filtered…
The Fe-Mn-based alloys are receiving immense attention due to their applications in the third generation of advanced high-strength steels, owing to their high strength and ductility. A detailed in situ high-pressure structural phase…
Precipitation in Mg-Zn alloys was analyzed by means of first principles calculations. Formation energies of symmetrically distinct hcp Mg1-xZnx (0 < x < 1) configurations were determined and potential candidates for Guinier-Preston zones…
Binary random compacts with different proportions of small (volume V) and large (volume 2V) bare maghemite nanoparticles (NPs) are used to investigate the effect of controllably broadening the particle size distribution on the magnetic…
The thermodynamic stability of the premartensite (PM) phase has been a topic of extensive investigation in shape memory alloys as it affects the main martensite phase transition and the related physical properties. In general, the PM phase…
Microstructural features and mechanical properties of an Al-Mg-Si alloy processed by high-pressure torsion have been investigated using transmission electron microscopy, X-ray diffraction, three-dimensional atom probe, tensile tests and…
A novel medium Mn steel of composition Fe-12Mn-4.8Al-2Si-0.32C-0.3V was manufactured with 1.09 GPa yield strength, 1.26 GPa tensile strength and 54% elongation. The thermomechanical process route was designed to be industrially translatable…
The mechanical properties of Mg-4wt.% Zn alloy single crystals along the [0001] orientation were measured through micropillar compression at 23C and 100C. Basal slip was dominant in the solution treated alloy, while pyramidal slip occurred…