Related papers: High Density Hybridisation Using ENIG Bumping and …
Single photon sensitivity is an important property of certain detection systems. This work investigated the single photon sensitivity of the Adaptive Gain Integrating Pixel Detector (AGIPD) and its dependence on possible detector noise…
Silicon nitride (Si$_3$N$_4$) photonic integrated circuits (PICs) have emerged as a versatile platform for a wide range of applications, such as nonlinear optics, narrow-linewidth lasers, and quantum photonics. While thin-film Si$_3$N$_4$…
A monolithic silicon pixel ASIC prototype, produced in 2024 as part of the Horizon 2020 MONOLITH ERC Advanced project, was tested with a 120 GeV/c pion beam. The ASIC features a matrix of hexagonal pixels with a 100 \mu m pitch, read by…
Low resolution analog-to-digital converters (ADCs) can be employed to improve the energy efficiency (EE) of a wireless receiver since the power consumption of each ADC is exponentially related to its sampling resolution and the hardware…
Indoor localization remains challenging in GNSS-denied environments due to multipath, device heterogeneity, and volatile radio conditions. We propose a topology-aware, hybrid Wi-Fi/BLE fingerprinting framework that (i) applies physically…
This paper proposes a novel non-orthogonal affine frequency division multiplexing (nAFDM) waveform for reliable high-mobility communications with enhanced spectral efficiency (SE). The key idea is to introduce a bandwidth compression factor…
Hybrid beamforming (HBF) and antenna selection are promising techniques for improving the energy efficiency~(EE) of massive multiple-input multiple-output~(mMIMO) systems. However, the transmitter architecture may contain several parameters…
We have studied the effect of nitriding on the humidity sensing properties of hydrogenated amorphous carbon (a-C:H) films. The films were prepared in two stages combining the techniques of physical deposition in vapor phase evaporation…
Microcombs have sparked a surge of applications over the last decade, ranging from optical communications to metrology. Despite their diverse deployment, most microcomb-based systems rely on a tremendous amount of bulk equipment to fulfill…
Lithium fluorinated carbon is one of the most promising chemistries for high-energy-density primary energy storage systems in applications where rechargeability is not required. Though Li/CFx demonstrates high energy density under ambient…
Demanding microwave applications in a magnetic field require the material optimization not only in zero-field but, more important, in the in-field flux motion dominated regime. However, the effect of artificial pinning centers (APC) remains…
Three-dimensional (3D) photonic integrated circuits (PIC) are emerging as an indispensable scheme for high density and multifunctional photonic systems. However, the wafer-scale scaling of PICs towards a 3D configuration is constrained by…
We explore theoretically the properties of engineered bimetallic nano-structured superlattices where an array of nano-clusters of a simple (single band) metal are embedded periodically inside another simple metal with a different work…
Among a variety of solution-based approaches to fabricate anisotropic films of aligned carbon nanotubes (CNTs), we focus on the dielectrophoretic assembly method using AC electric fields in DNA-stabilized CNT suspensions. We demonstrate…
Integrated nonlinear photonic technologies, even with state-of-the-art fabrication with only a few nanometer geometry variations, face significant challenges in achieving wafer-scale yield of functional devices. A core limitation lies in…
Hybrid beamforming (HBF) is an attractive technology for practical massive multiple-input and multiple-output (MIMO) millimeter wave (mmWave) systems. Compared with the fully-connected HBF architecture, the partially-connected one can…
Hybridisation is a powerful strategy towards the next generation of multifunctional materials for environmental and sustainable energy applications. Here, we report a new inorganic nanocarbon hybrid material prepared with atomically…
Metrological AFM measurements are performed on the silica glass interfaces of photonic band-gap fibres and hollow capillaries. The freezing of attenuated out-of-equilibrium capillary waves during the drawing process is shown to result in a…
This paper presents a new research study on the platform fabrication of fluorescence bio-detection chip with an optical fiber transmission. Anisotropic wet etching on (100) silicon wafers to fabrication V-groove for optical fiber alignment…
The demand for edge AI in vision-language tasks requires models that achieve real-time performance on resource-constrained devices with limited power and memory. This paper proposes two adaptive compression techniques -- Sparse Temporal…