Related papers: Master Oscillator and Phase Reference Line Design …
The Fermilab Linac delivers 400 MeV H- beam to the rest of the accelerator chain. Providing stable intensity, energy, and emittance is key since it directly affects downstream machines. To operate high current beam, accelerators must…
The LLRF of five of TRIUMF's ISAC-1 accelerator cavities have been replaced by 3 similar FPGA based system with different operating frequencies. These LLRF use internal digital phase locked loops for frequency generation and…
Increasing the Fermilab Main Injector (MI) beam power above ~1.2 MW requires replacement of the 8 GeV Booster by a higher intensity alternative. Earlier, rapid-cycling synchrotron and linac solutions were considered for this purpose. In…
The construction of the initial part of a normally conducting linac for hydrogen ion beams with a pulsed current of ~20 mA up to an energy of ~70 MeV is considered. The RFQ at a frequency of ~160 MHz accelerates ions to an energy of ~4 MeV.…
The ongoing work to upgrade ALS to ALS-U demands strict RF requirements such as low jitter and low spurs frequency reference to meet its accelerator and science goals. A low phase noise dual frequency Master Oscillator (MO), where the two…
The LCLS-II HE superconducting linac can produce multi-energy beams by supporting multiple undulator lines simultaneously. This could be achieved by using the cavity SRF tuner in the off-frequency detune mode. This off-frequency operation…
The energy of a bunched non-relativistic ion beam can be deduced from measuring the beam phases in neighbouring Beam Position Monitors (BPMs). This report discusses implementation of such a procedure at the PIP-II H- linac being constructed…
Following the PIP-II 800 MeV Linac, Fermilab will need an accelerator that extends from that linac to the MI injection energy of ~8 GeV, completing the modernization of the Fermilab high-intensity accelerator complex. This will maximize the…
Phase noise (PN) is a major disturbance in MIMO systems, where the contribution of different oscillators at the transmitter and the receiver side may degrade the overall performance and offset the gains offered by MIMO techniques. This is…
Five 325 MHz high-power couplers will be integrated into the pre-production Single Spoke Resonator Type-II (ppSSR2) cryomodule for the PIP-II project at Fermilab. Couplers were procured by both Fermilab and IJCLAB for this effort. The…
Phase noise (PN) is a critical impairment at D-band frequencies (110 to 170 GHz), which are widely investigated as promising candidates for beyond 5G/6G ISAC systems. This paper evaluates OFDM based ISAC sensing performance under realistic…
For the PIP-II Injector Test (PI-Test) at Fermilab, a four-vane radio frequency quadrupole (RFQ) is designed to accelerate a 30-keV, 1-mA to 10-mA, H- beam to 2.1 MeV under both pulsed and continuous wave (CW) RF operation. The available…
Optical properties of components in a linac can be reconstructed from analysis of the orbit response matrix, composed from responses of BPMs to changes in currents of dipole correctors. An efficient way to record such response, discussed in…
Multi-phase injection-locked ring oscillators (MP-ILROs) are widely used for multi-phase clock generation, with their phase accuracy primarily determined by the inherent accuracy of the oscillator itself, due to the suppression of input…
The coax based MO distribution system in the ALS is going to be replaced by a modernized, lower phase noise and more interference tolerant version, ready to support ALS-U operation. System aspects are shown and several commercial analog and…
The Proton Improvement Plan II (PIP-II) project is an essential upgrade to Fermilab's particle accelerator complex to enable the world's most intense neutrino beam for LBNF/DUNE and a broad particle physics program for many decades to come.…
A 162.5 MHz, 2.1 MeV Radio Frequency Quadruples (RFQ) structure is being designed for the Injector Scheme II of China Accelerator Driver System (CADS) driver linac. The RFQ will operate at continuous wave (CW) mode as required. For the CW…
"LUE200" - 200 MeV electron linac is being created at JINR as a driver of the pulsed neutron source "IREN" [1]. The special full-scale facilities for testing the main systems of LUE-200 (FSTF) are used at JINR, BINP, MEPhI and YerPhI [2].…
The paper proposes a method of finding the beam loss locations in a linac. If the beam is scraped at an aperture limitation, moving its centroid with two dipole correctors located upstream and oscillating in sync produces a line at the…
The output of oscillators is usually not stable over time. In particular, phase variations---or \emph{phase noise}---corrupts the oscillations. In this letter, we describe a circuit that designed to average the phase noise processes and…