Related papers: Deformation mechanisms of L-PBF-processed Ti-6Al-4…
Laser powder bed fusion (L-PBF) of semi-crystalline polymers such as polyamide-12 (PA12) has found increasing use in various industrial applications. However, achieving high dimensional accuracy remains a significant challenge. Despite the…
Additive manufacturing of Ti-6Al-4V alloy via laser powder-bed fusion leads to non-equilibrium $\alpha'$ martensitic microstructures, with high strength but poor ductility and toughness. These properties may be modified by heat treatments,…
The elasto-plastic material behavior, material strength and failure modes of metals fabricated by additive manufacturing technologies are significantly determined by the underlying process-specific microstructure evolution. In this work a…
The microstructure of Ti-6Al-4V has a decisive impact on its mechanical performance; however, controlling phase composition during Laser Powder Bed Fusion (LPBF) remains difficult because of the inherent localized and cyclic thermal…
We study the evolution of prior columnar $\beta$ phase, interface $L$ phase, and $\alpha$ phase during directional solidification of a Ti-6Al-4V melt pool. Finite element simulations estimate the solidification temperature and velocity…
The ability to create complex geometries with tailored material properties has brought interest in using additive manufacturing (AM) techniques in various industrial applications. However, the complex relationship between AM process…
As structural and functional materials, topologically close-packed (TCP) phases of transition metal compounds offer a wide range of attractive properties. Due to their complex crystal structure and the resulting brittleness, the knowledge…
Detailed microstructure characterisation and in-situ micropillar compression were coupled with crystal plasticity-based finite element modelling (CP-FEM) to study the micro-mechanisms of plastic anisotropy in lamellar TiAl alloys. The…
This study demonstrates the significant effect of the recoil pressure and Marangoni convection in laser powder bed fusion (L-PBF) of 316L stainless steel. A three-dimensional high fidelity powder-scale model reveals how the strong dynamical…
The role of TCP phases in deformation of superalloys and steels is still not fully resolved. In particular, the intrinsic deformation mechanisms of these phases are largely unknown including the active slip systems in most of these complex…
The processing of binary alloys consisting of ferromagnetic Fe and antiferromagnetic Cr by severe plastic deformation (SPD) with different chemical compositions has been investigated. Although the phase diagram exhibits a large gap in the…
The alpha/beta interface in Ti-6Al-2Sn-4Zr-6Mo (Ti-6246) is investigated via centre of symmetry analysis, both as-grown and after 10% cold work. Semi-coherent interface steps are observed at a spacing of 4.5 +/-1.13 atoms in the as-grown…
Rapid cooling rates and stochastic interactions between the heat source and feedstock in additive manufacturing (AM) result in strong anisotropy and process-induced defects deteriorating the tensile ductility and fatigue resistance of…
SrAl2Si2 crystallizes into either a semimetallic, CaAl2Si2-type, \alpha phase or a superconducting, BaZn2P2-type, \beta phase. We explore possible \alpha --Pc;Tc--> \beta transformations by employing pressure- and temperature-dependent…
The mimicry of crystalline microstructure at meso-scale creates a new class of architected materials, termed meta-crystals, and offers effective ways to significantly improve the toughness and eliminate the post-yield collapse of…
The mitigation of material defects from additive manufacturing (AM) processes is critical to reliability in their fabricated parts and is enabled by modeling the complex relations between available build monitoring signals and final…
The microstructure of Mg-Al-Ca alloys consists of a hard intra- and intergranular eutectic Laves phase network embedded in a soft $\alpha$-Mg matrix. For such heterogeneous microstructures, the mechanical response and co-deformation of both…
Aiming to simulate the radiation damage effect on a dual alpha+beta phase Ti-6Al-4V alloy utilized as high-intensity accelerator beam window material, a series of irradiation experiments were conducted with a 2.8 MeV-Fe^2+ ion beam in…
Amorphization during severe plastic deformation has been observed in various crystalline materials, yet its underlying mechanisms remain poorly understood. This study introduces a novel phase-field model at the mesoscale, integrating…
We consider the process of precipitation in binary alloys in the presence of mechanical deformation. It is commonly observed that mechanical deformation prior to or during precipitation leads to microstructure with excess defects, which…