Related papers: A Wide-Input 0.25 um BCD LDO with Dual-Stage Ampli…

This paper presents the design and analysis of a wearable CMOS biosensor with three different designs of energy-resolution scalable time-based resistance to digital converters (RDC), targeted towards either minimizing the energy/conversion…

This paper present high precision halfwave rectifier circuit in dual phase output mode by 0.5 micrometer CMOS technology, plus or minus 1.5 V low voltage, it has received input signal and sent output current signal, respond in high…

We present a spectroscopic system constituted by a Silicon Drift Detector (SDD) coupled to a CMOS charge sensitive preamplifier, named SIRIO, specifically designed to reach ultimate low noise levels. The SDD, with an active area of 13 mm ,…

This work presents a new frequency acquisition method using semi-rotational frequency detection (SRFD) algorithm for a reference-less clock and data recovery (CDR) in a serial-link receiver. The proposed SRFD algorithm classifies the…

This paper presents a low power, low cost transceiver architecture to implement radar-on-a-chip. The transceiver comprises of a full ultra-wideband (UWB) transmitter and a full UWB band receiver. A design methodology to maximize the tuning…

A series of simple and low-cost devices for switching, amplifying, and chirping diode lasers based on current modulation are presented. Direct modulation of diode laser currents is rarely sufficient to establish precise amplitude and phase…

The memristor, because of its controllability over a wide dynamic range of resistance, has emerged as a promising device for data storage and analog computation. A major challenge is the accurate measurement of memristance over a wide…

This paper investigates a joint beamforming design in a multiuser multiple-input single-output (MISO) communication network aided with an intelligent reflecting surface (IRS) panel. The symbol-level precoding (SLP) is adopted to enhance the…

This article is present high precision multiwave rectifier circuit operating in low voltage plus or minus 1.5 Volt current modes by CMOS technology 0.5 \mum, receive input and give output in current mode, respond at high frequency period.…

A radio frequency (RF) power amplifier (PA) plays an important role to amplify the message signal at higher power to transmit it to a distant receiver. Due to a typical nonlinear behavior of the PA at high power transmission, a digital…

In this paper, we propose and evaluate two novel double-sequence low-resolution frequency synchronization methods in millimeter-wave (mmWave) systems. In our system model, the base station uses analog beams to send the synchronization…

Clock generators are an essential and critical building block of any communication link, whether it be wired or wireless, and they are increasingly critical given the push for lower I/O power and higher bandwidth in Systems-on-Chip (SoCs)…

Multiple-input, multiple-output (MIMO) technology provides high data rate and enhanced QoS for wireless com- munications. Since the benefits from MIMO result in a heavy computational load in detectors, the design of low-complexity…

This work reports the performance evaluation of an SDR readout system based on the latest generation (Gen3) of the AMD's Radio Frequency System-on-Chip (RFSoC) processing platform, which integrates a full-stack processing system and a…

Distributed hardware of acoustic sensor networks bears inconsistency of local sampling frequencies, which is detrimental to signal processing. Fundamentally, sampling rate offset (SRO) nonlinearly relates the discrete-time signals acquired…

The task of this work was to design and later produce a low-power (single supply 5 - 30 V, dual supply +-2.5 V and +-15 V) rail-to-rail operational amplifier aRD820 with low voltage noise (<4 uV, p-p. 0.1 to 10 Hz), ultralow input bias…

We present an ultra-low noise, high-voltage driver suited for use with piezoelectric actuators and other low-current applications. The architecture uses a flyback switching regulator to generate up to 250V in our current design, with an…

Dynamic comparators are an essential part of low-power analog to digital converters (ADCs) and are referred to as one of the most important building blocks in mixed mode circuits. The power consumption and accuracy of dynamic comparators…

We present a high performance low-power digital base-band architecture, specially designed for an energy optimized duty-cycled wake-up receiver scheme. Based on a careful wake-up beacon design, a structured wake-up beacon detection…

Analog-to-Digital Converters (ADCs) are essential components in modern data acquisition systems. A key design challenge is accommodating high dynamic range (DR) input signals without clipping. Existing solutions, such as oversampling,…