Related papers: Enhanced strain rate sensitivity due to platelet l…
We study spacing selection in directional solidification of Al-Cu alloys under transient growth conditions. New experimental results are presented which reveal that dendritic spacing versus solidification rate evolves in an almost step-wise…
Dimension reduction procedure is the recipe to represent defects in two dimensional dislocation dynamics according to the changes in the geometrical properties of the defects triggered by different conditions such as radiation, high…
We study the elastic response of concentrated suspensions of rigid wire frame particles to a step strain. These particles are constructed from infinitely thin, rigid rods of length $L$. We specifically compare straight rod-like particles to…
We examine the atomistic scale dependence of material's resistance-to-failure by numerical simulations and analytical analysis in electrical analogs of brittle crystals. We show that fracture toughness depends on the lattice geometry in a…
The recrystallized grain size and texture in alloys can be controlled via the microchemistry state during thermomechanical processing. The influence of concurrent precipitation on recovery and recrystallization is here analyzed by directly…
Surface roughness affects many properties of colloids, from depletion [1] and capillary interactions [2], to their dispersibility [3] and use as emulsion stabilizers [4]. It also impacts particle-particle frictional contacts, which have…
The softening and strengthening contributions in pre-deformed and aged Al-Mg-Cu alloys containing 3wt.%Mg and 0.5wt.%Cu are evaluated by a combination of microscopy, mechanical testing and modelling. A refined phenomenological model for the…
Thick-section plates made from a recently developed Al-Cu-Mg-Li alloy have been evaluated to understand the influence of microstructure on the anisotropy of tensile strengths after natural and artificial ageing treatment. Pancake-shaped…
The stress-driven motion of dislocations in crystalline solids, and thus the ensuing plastic deformation process, is greatly influenced by the presence or absence of various point-like defects such as precipitates or solute atoms. These…
In this work electron backscattered diffraction (EBSD)-assisted slip trace analysis and transmission electron microscopy have been utilized to investigate the interaction of basal dislocations with precipitates in the Mg alloys…
This work is a continuation of the ongoing research on deformation behavior of reinforced concrete elements under tension. The previous studies have revealed that deformation behaviors of elements reinforced with multiple bars and the…
Identified charged pion, kaon, and proton spectra are used to explore the system size dependence of bulk freeze-out properties in Cu+Cu collisions at $\sqrt{s_{NN}}$=200 and 62.4 GeV. The data are studied with hydrodynamically-motivated…
Complex morphologies and microstructures that emerge during materials growth and solidification are often determined by both equilibrium and kinetic properties of the interface and their crystalline anisotropies. However limited knowledge…
While perfect crystals may exhibit a purely elastic response to shear all the way to yielding, the response of amorphous solids is punctuated by plastic events. The prevalence of this plasticity depends on the number of particles $N$ of the…
The universality class of the avalanche behavior in plastically deforming crystalline and amorphous systems has been commonly discussed, despite the fact that the microscopic defect character in each of these systems is different. In…
The effect of elastic strain on catalytic activity of platinum (Pt) towards oxygen reduction reaction (ORR) is investigated through de-alloyed Pt-Cu thin films; stress evolution in the de-alloyed layer and the mass of the Cu removed are…
The present work investigates the atomic interactions among Cu, Al, and Ni elements in bcc-iron matrix, focusing on the formation mechanism of nano-sized core-shell Cu precipitates. Using a combination of atom probe tomography (APT),…
We use computer simulations to study the behavior of atomically sharp and blunted cracks in various f.c.c. metals. The simulations use effective medium potentials which contain many-body interactions. We find that when using potentials…
Dislocations are topological defects known to be crucial in the onset of plasticity and in many properties of crystals. Classical Elasticity still fails to fully explain their dynamics under extreme conditions of high strain gradients and…
The mechanical properties of Cu/Nb metallic nanolaminates with different layer thickness (7, 16, 34 and 63 nm) were studied by means of micropillar compression tests from room temperature to 400 C. Both strain-rate jump and constant strain…