Related papers: Latch Based Design for Fast Voltage Droop Response
Emergency control, typically such as under-voltage load shedding (UVLS), is broadly used to grapple with low voltage and voltage instability issues in practical power systems under contingencies. However, existing emergency control schemes…
We present hardware/software techniques to intelligently regulate supply voltage and clock frequency of intermittently-computing devices. These devices rely on ambient energy harvesting to power their operation and small capacitors as…
This paper presents a novel load frequency control (LFC) design using integral-based decentralize fixed-order perturbed dynamic output tracking scheme in a delay dependent nonlinear interconnected multi-area power system via LMI approach.…
We propose a high-performance atomic clock based on the 1.81 PHz transition between the ground and first-excited state of doubly ionized lead. Utilizing an even isotope of lead, both clock states have $I=J=F=0$, where $I$, $J$, and $F$ are…
Locally resonant elastic metamaterials (LREM) can be designed, by optimizing the geometry of the constituent self-repeating unit cells, to potentially damp out vibration in selected frequency ranges, thus yielding desired bandgaps. However,…
This paper presents a novel strategy for the synchronization of grid-following Voltage Source Converters (VSCs) in power systems with low rotational inertia. The proposed synchronization unit is based on emulating the physical properties of…
The experimental study of two kinds of electrical circuits, a domino ladder and a nested ladder, is presented. While the domino ladder is known and already appeared in the theory of fractional-order systems, the nested ladder circuit is…
This paper presents an output capacitor-less low-dropout regulator (LDO) with a bias switching scheme for biomedical applications with dual-range load currents. Power optimization is crucial for systems with multiple activation modes such…
Ever-increasing design complexity of System-on-Chips (SoCs) led to significant verification challenges. Unlike software, bugs in hardware design are vigorous and eternal i.e., once the hardware is fabricated, it cannot be repaired with any…
In various of particle accelerator designs, amplitude and phase modulation methods are commonly applied to shape the RF pulses for implementing pulse compressors or compensating for the fluctuations introduced by the high-power RF…
Extensive literature has shown that finite impulse response (FIR) interferometers can be engineered to be insensitive under variations of different physical parameters, e.g., to ensure flat-top response and/or tolerance to fabrication…
The paper addresses the exact linearization of flat nonlinear discrete-time systems by generalized static or dynamic feedbacks which may also depend on forward-shifts of the new input. We first investigate the question which forward-shifts…
Rapid acceleration and burst maneuvers in underwater robots depend less on maintaining precise resonance and more on force--velocity phase alignment during thrust generation. In this work, we investigate constrained-layer damping (CLD) as a…
It was recently shown that the use of feedback control can improve the performance of a flashing ratchet. We investigate the effect of a time delay in the implementation of feedback control in a closed-loop collective flashing ratchet,…
Routing of the nets in Field Programmable Gate Array (FPGA) design flow is one of the most time consuming steps. Although Versatile Place and Route (VPR), which is a commonly used algorithm for this purpose, routes effectively, it is slow…
High-voltage direct current (HVDC) transmission applications and the growth of the dynamic load in large-scale receiving-end grids lead to a higher risk of short-term voltage instability. An effective way to address this problem is to…
Processing sensor data with spiking neural networks on digital neuromorphic chips requires converting continuous analog signals into spike pulses. Two strategies are promising for achieving low energy consumption and fast processing speeds…
Synchronous reference frame phase-looked loop (SRF-PLL) techniques are widely used for interfacing and control applications in the power systems and energy conversion at large. Since a PLL system synchronizes its output with an exogenous…
Phase shaping using fractional order (FO) phase shapers has been proposed by many contemporary researchers as a means of producing systems with iso-damped closed loop response due to a stepped variation in input. Such systems, with the…
Electrical control of oxygen off-stoichiometry of transition-metal oxides at room temperature is a desired strategy to simultaneously switch the electrical conductance and magnetism of the device. Although the use of the electrochemical…