Related papers: A novel simulation approach for concentration-driv…
Subsurface sequestration of CO2 has received attention from the global scientific community in response to climate change concerns due to higher concentrations of CO2 in the atmosphere. Mathematical models have thus been developed to aid…
Predicting the spatial configuration of gas molecules in nanopores of shale formations is crucial for fluid flow forecasting and hydrocarbon reserves estimation. The key challenge in these tight formations is that the majority of the pore…
The present study reports a novel physical model for simulating Pulsating Heat Pipes (PHP). Their high heat performance is due to the phase change over thin liquid films. The simulation of physically correct film behavior is thus crucial.…
We investigate a two-dimensional network simulator that model the dynamics of two-phase immiscible bulk flow where film flow can be neglected. We present a method for simulating the detailed dynamical process where the two phases are…
It is the purpose of this work to develop new approach for chemical compositional reservoir simulation, which may be regarded as a sequential method. The development process can be roughly divided into the following two stages: (1)…
It is shown that a bare simple fluid model (SFM) proposed some years ago for studying adsorption between two semi-infinite solid walls can be improved by modifying the surface term in the grand potential for the film phase. Such a…
Surface tension-driven flow techniques have recently emerged as an efficient means of shedding light into the rheology of thin polymer films. Motivated by experimental and theoretical approaches in films bearing a varying surface…
We present a new Eulerian framework for the computation of turbulent compressible multiphase channel flows, specifically to assess turbulence modulation by dispersed particulate matter in dilute concentrations but with significant mass…
We develop a novel Moving Particle Simulation (MPS) method to accurately reproduce the motion of fibers floating in sheared liquids. In conventional MPS schemes, if a fiber suspended in a liquid is represented by a one-dimensional array of…
Modern computing clusters offer specialized hardware for reduced-precision arithmetic that can speed up the time to solution significantly. This is possible due to a decrease in data movement, as well as the ability to perform arithmetic…
This paper investigates numerically the hydraulic conveying of solids through a 90$^{\circ}$ elbow that changes the flow direction from horizontal to vertical, in the very-narrow case where the ratio of pipe to particle diameters is less…
Hypothesis: A broad range of phenomena, such as emulsification and emulsion stability, foam formation or liquid evaporation, are closely related to the dynamics of adsorbing colloidal particles. Elucidation of the mechanisms implied is key…
Droplet evaporation in turbulent sprays involves unsteady, multiscale and multiphase processes which make its comprehension and model capabilities still limited. The present work aims to investigate droplet vaporization dynamics within a…
Mixtures of fluids and granular sediments play an important role in many industrial, geotechnical, and aerospace engineering problems, from waste management and transportation (liquid--sediment mixtures) to dust kick-up below helicopter…
The dynamics of compressible liquid-vapor flow depends sensitively on the microscale behavior at the phase boundary. We consider a sharp-interface approach, and propose a multiscale model to describe liquid-vapor flow accurately, without…
The aim of this work is to develop a new numerical method to overcome the computational difficulties of numerical simulation of unsaturated impregnation in porous media. The numerical analysis by classical methods (F.E.M, theta-method, ...)…
In many spinning processes, as for example in dry spinning, solvent evaporates out of the spun jets and leads to thinning and solidification of the produced fibers. Such production processes are significantly driven by the interaction of…
Modelling the sudden depressurisation of superheated liquids through nozzles is a challenge because the pressure drop causes rapid flash boiling of the liquid. The resulting jet usually demonstrates a wide range of structures, including…
The task of accurately locating fluid phase boundaries by means of computer simulation is hampered by problems associated with sampling both coexisting phases in a single simulation run. We explain the physical background to these problems…
In this work we present, for the first time, a computational fluid dynamics tool for the simulation of the metered discharge in a pressurized metered dose inhaler. The model, based on open-source software, adopts the Volume-Of-Fluid method…