Related papers: Low-Complex Waveform, Modulation and Coding Design…

Bit-interleaved coded modulation (BICM) has attracted considerable attention from the research community in the past three decades, because it can achieve desirable error performance with relatively low implementation complexity for a large…

Future cellular systems based on the use of millimeter waves will heavily rely on the use of antenna arrays both at the transmitter and at the receiver. For complexity reasons and energy consumption issues, fully digital precoding and…

To enable larger apertures in multipleinput multipleoutput MIMO systems the trihybrid MIMO architecture offers a promising lowcost and lowpower solution by introducing reconfigurable antennas as a third layer of precoding on top of…

Ambient backscatter communication (AmBC) over orthogonal-frequency-division-multiplexing (OFDM) signals has recently been proposed as an appealing technique for low power Internet-of-Things (IoT) applications. The special spectrum structure…

The Narrowband Internet of Things (NB-IoT) is a cellular access technology developed by the Third Generation Partnership Project (3GPP) to provide wide area connectivity for the Internet of Things. Since its introduction in 3GPP Release 13,…

Small, low-cost IoT devices are typically equipped with only a single, low-quality antenna, significantly limiting communication range and link quality. In particular, these antennas are typically linearly polarized and therefore…

Energy efficiency has emerged as a defining constraint in the evolution of sustainable Internet of Things (IoT) networks. This work moves beyond simulation-based or device-centric studies to deliver measurement-driven, network-level smart…

For many applications envisioned for the Internet of Things (IoT), it is expected that the sensors will have very low costs and zero power, which can be satisfied by meta-material sensor based IoT, i.e., meta-IoT. As their constituent…

This paper proposes a complete IFoF system architecture derived from simplified IEEE802.15.3c PHY layer proposal to successfully ensure near 1 Gbps on the air interface. The system architecture utilizes low complexity baseband processing…

In the last decade, the advancement of the Internet of Things (IoT) has caused unlicensed radio spectrum, especially the 2.4 GHz ISM band, to be immensely crowded with smart wireless devices that are used in a wide range of application…

Future wireless communication systems must simultaneously address multiple challenges to ensure accurate data detection, deliver high Quality of Service (QoS), adding enable a high data transmission with low system design. Additionally,…

Air interface is a fundamental component within any wireless communication system. In Release 18, the 3rd Generation Partnership Project (3GPP) delves into the possibilities of leveraging artificial intelligence (AI)/machine learning (ML)…

This paper reports on 3D-printed dielectric image lines for low-loss subTHz applications between 140 and 220 GHz. In contrast to conventional dielectric waveguides, a conductive copper substrate is used to achieve robust routing and…

High-speed optical wireless communication can address the exponential growth in data traffic. Adaptive beamforming customized for the target location is crucial, but existing solutions such as liquidcrystal spatial light modulators and…

In order to meet the demands of `Internet above the clouds', we propose a multiple-antenna aided adaptive coding and modulation (ACM) for aeronautical communications. The proposed ACM scheme switches its coding and modulation mode according…

Due to the rapidly increasing number of flights and high usage of VHF channels, the VHF spectrum is becoming much more crowded, and use of analog waveforms will likely not maintain the required performance. Therefore, digital communications…

In this paper, for the first time, we propose two new solutions to boost the data rate between small connected objects such as glasses and cams and the 5th generation (5G) mobile network, based on spatial modulation, single carrier…

In this paper, we aim to design highly energy efficient end-to-end communication for millimeter wave multiple-input multiple-output systems. This is done by jointly optimizing the digital-to-analog converter (DAC)/analog-to-digital…

This paper bridges this critical gap by providing a systematic examination of the beamforming codebook technology, i.e., precoding matrix indicator (PMI), in the 5G NR from theoretical, standardization, and implementation perspectives. We…

We investigate antenna coding utilizing pixel antennas as a new degree of freedom for enhancing multiple-input multiple-output (MIMO) wireless power transfer (WPT) systems. The objective is to enhance the output direct current (DC) power…