Related papers: Finite Element Analysis of Shear Lag Effect in Lon…
Shear transformations (i.e., localised rearrangements of particles resulting in the shear deformation of a small region of the sample) are the building blocks of mesoscale models for the flow of disordered solids. In order to compute the…
Unlike influence lines, the concept of influence zones is remarkably absent within the field of structural engineering, despite its existence in the closely related domain of geotechnics. This paper proposes the novel concept of a…
The stability of dry-snow avalanches is strongly dependent on the interaction between the snow slab above a weak-layer and, as presented in this work, the skier induced load. This induced load causes an additional stress field on the slab…
Metal rolling is a widespread and well-studied process, and many finite-element (FE) rolling simulations can be found in the scientific literature. However, these FE simulations are typically limited in their resolution of through-thickness…
We report on experimentally observed shear stress fluctuations in both granular solid and fluid states, showing that they are non-Gaussian at low shear rates, reflecting the predominance of correlated structures (force chains) in the…
Aeroelastic model testing is essential for evaluating the wind resistance performance of long-span suspension bridges. In these models, truss girders are commonly modelled by a discrete-stiffness system incorporating U-shaped springs to…
Crystalline plasticity is strongly interlinked with dislocation mechanics and nowadays is relatively well understood. Concepts and physical models of plastic deformation in amorphous materials on the other hand - where the concept of linear…
In this research, a new analytical model is developed to analyze structural members strengthened with FRP systems and subjected to impact loading conditions. ABAQUS based finite element code was used to develop the proposed model. The model…
Yield stress fluids (YSFs) display a dual nature highlighted by the existence of a yield stress such that YSFs are solid below the yield stress, whereas they flow like liquids above it. Under an applied shear rate $\dot\gamma$, the…
The immersed finite element-finite difference (IFED) method is a computational approach to modeling interactions between a fluid and an immersed structure. This method uses a finite element (FE) method to approximate the stresses and forces…
An accurate description of elastic effects of coherent microstructures is necessary for the predictive modeling of microstructural evolution in many structural materials. To date, there has not been a demonstration on how continuum…
To elucidate the key factor for the quantitative prediction of the shear-thickening in suspensions in viscoelastic fluids, direct numerical simulations of many-particle suspensions in a multi-mode Oldroyd-B fluid are performed using the…
A comparative analysis of two bridges constructed with the most commonly used girder types in Florida is carried out. The girder types that the bridges are employed for this study are AASHTO Type III (American Association of State Highway…
In this work, an efficient and robust isogeometric three-dimensional solid-beam finite element is developed for large deformations and finite rotations with merely displacements as degrees of freedom. The finite strain theory and…
We have performed surface tension measurements on carbopol gels of different concentrations and yield stresses. Our setup, based on the force exerted by a capillary bridge on two parallel plates, allows to measure an effective surface…
Repetitive loading of bone is associated with microdamage accumulation and material property degradation that may ultimately result in fatigue fracture. Our previous work used continuum damage mechanics (CDM)-based finite element (FE)…
This study investigates how the deposit body influences friction characteristics by altering local flow fields, which is closely related to bed shear stress. Using generalized flume experiments, the study assesses the applicability of…
The layer-upon-layer approach in additive manufacturing, open or closed cells in polymeric or metallic foams involve an intrinsic microstructure tailored to the underlying applications. Homogenization of such architectured materials creates…
Rate-effects in sheared disordered solids are studied using molecular dynamics simulations of binary Lennard-Jones glasses in two and three dimensions. In the quasistatic (QS) regime, systems exhibit critical behavior: the magnitudes of…
Shearing stresses can change the volume of a material via a nonlinear effect known as shear dilatancy. We calculate the elastic dilatancy coefficient of soft sphere packings and random spring networks, two canonical models of marginal…