Related papers: PCB Transducer Coil Design for a Low-Noise Magneti…
We present a magnetic field confining coil with a sub-$10^{-3}$ field uniformity over a large fraction of the coil. The structure is entirely made out of printed circuit boards (PCBs). The PCB design allows to tailor the path of wires to…
Using oscillating magnetic fields for indoor positioning is a robust way to resist dynamic environments. This work presents the hard- and software-related optimizations of an induced magnetic field positioning system. We describe a new coil…
Optimizing sensor readout schemes and integrated circuit designs for both open-loop and closed-loop implementations requires precise modeling and simulation strategies. This study introduces a novel two-port impedance model to estimate the…
Inertial sensors that measure the acceleration of ultracold atoms promise unrivalled accuracy compared to classical equivalents. However, atomic systems are sensitive to various perturbations, including magnetic fields, which can introduce…
'Coil design' is an inverse problem in which arrangements of wire are designed to generate a prescribed magnetic field when energized with electric current. The design of gradient and shim coils for magnetic resonance imaging (MRI) are…
Quantum sensors based on cold atoms are being developed which produce measurements of unprecedented accuracy. Due to shifts in atomic energy levels, quantum sensors often have stringent requirements on their internal magnetic field…
Rotor position feedback is required in many industrial and automotive applications, e.g. for field-oriented control of brushless motors. Traditionally, magnetic sensors, resolvers or optical encoders are used to measure the rotor position.…
A high-accuracy calibration of inductive coil sensors based on Printed Circuit Board (PCB), commonly used in rotating coil field measurements of particle accelerator magnets, is presented. The amplitude and phase of signals with and without…
The use of Printed Circuit Boards (PCBs) for the inductive pick-up windings of rotating coil probes has made the construction of these precision magnetic measurement devices much more accessible. This paper discusses the design details for…
A two-core transducer assembly using a Fe73.5Nb3Cu1Si13.5B9 ribbon to detect a change of magnetic field is proposed and tested for displacement (linear and angular) and current sensor. Two identical inductors, with the ribbon as core, are a…
For the generation of static magnetic fields solenoids are frequently used for the purpose of research and development of magnetic field sensors. When such a sensor is to be analyzed with regard to its inherent noise the influence of other…
A conduction-cooled superconducting magnet producing a transverse field of 4 Tesla has been designed for the new generation multi-field coupling measurement system, which was used to study the mechanical behavior of superconducting samples…
Here, a generalized induction coil sensor model, more generalized than other models, has been considered and the equivalent magnetic field of the coil thermal noise and the sensor signal to noise ratio are calculated theoretically based on…
In this paper we present a portable magnetocardiography device. The focus of this development was delivering a rapid assessment of chest pain in an emergency department. The aim was therefore to produce an inexpensive device that could be…
The design and performance of a sensitive and reliable cross-correlation spectrum analyzer for studying low frequency transport noise is described in detail. The design makes use of common PC-based data acquisition hardware and…
Atomic spin sensors offer precision measurements using compact, microfabricated packages, placing them in a competitive position for both market and research applications. Performance of these sensors such as dynamic range may be enhanced…
We present a computational framework for the design of magnonic transducers, where waveguide antennas generate and pick up spin-wave signals. Our method relies on the combination of circuit-level models with micromagnetic simulations and…
This study presents the design, simulation, and experimental characterization of a superconducting transmon qubit circuit prototype for potential applications in dark matter detection experiments. We describe a planar circuit design…
Objective: This work aims to reduce the acoustic noise level of transcranial magnetic stimulation (TMS) coils. TMS requires high currents (several thousand amperes) to be pulsed through the coil, which generates a loud acoustic impulse…
Cold atoms experiments employ magnetic fields, commonly generated by coils, as an essential tool to control and manipulate atomic samples. In these experiments, it is often necessary to rapidly switch the magnetic field between two values.…