Related papers: Surface molecular engineering to enable processing…
MnxOy coated over TiO2 nanotube array substrate was doped with Mo and polyaniline (PANI) and applied for electrochemical desulfurization of concentrated sulfide (HS) solutions at basic pH, typical of biogas scrubbing solutions and…
Among the 'beyond Li-ion' battery chemistries, nonaqueous Li-O$_2$ batteries have the highest theoretical specific energy and as a result have attracted significant research attention over the past decade. A critical scientific challenge…
Intrinsic hydrogenated amorphous silicon films can provide outstanding surface passivation of crystalline silicon wafer surfaces. This quality of Intrinsic hydrogenated amorphous silicon makes it valuable in heterojunction with intrinsic…
Time of Flight Secondary Ion Mass Spectroscopy, X-Ray Photoelectron Spectroscopy, in situ Photo-Current Spectroscopy and electrochemical analysis were combined to characterize the physicochemical alterations induced by electrochemical…
In high power RF devices for space, secondary electron emission appears as the main parameter governing the multipactor effect and as well as the e-cloud in large accelerators. Critical experimental activities included development of…
Water-in-Salt-Electrolytes (WiSEs) are a promising class of next-generation electrolytes. Unlike classical dilute electrolytes or more conventional battery electrolytes, WiSEs are characterised by their super-concentrated salt concentration…
Battery interfaces help govern rate capability, safety/stability, cycle life, and self-discharge, but significant gaps remain in our understanding at atomic length scales that can be exploited to improve interfacial properties. In…
Solid polymer electrolytes for lithium batteries promise improvements in safety and energy density if their conductivity can be increased. Nanostructured block copolymer electrolytes specifically have the potential to provide both good…
Solid-state dewetting (SSD), a widespread phenomenon in solid-solid-vapor system, could be used to describe the accumulation of solid thin films on the substrate. In this work, we consider the sharp interface model for axisymmetric SSD with…
The use of self-assembled monolayers (SAMs) with anchoring groups was considered as an effective approach for interface engineering in perovskite solar cells with metal oxide charge transporting layers. However, the coating of SAM layers in…
Low cost, highly efficient, and stable solar cells demand low temperature processing, less stringent criteria on materials, and possibility of dynamic recovery from long term degradation: a combination of features unachievable from the…
Improvements in circuit design and more recently in materials and surface cleaning have contributed to a rapid development of coherent superconducting qubits. However, organic resists commonly used for shadow evaporation of Josephson…
As an anode material for lithium-ion batteries, amorphous silicon offers a significantly higher energy density than the graphite anodes currently used. Alloying reactions of lithium and silicon, however, induce large deformation and lead to…
Multi-valent (MV) battery architectures based on pairing a Mg metal anode with a high-voltage ($\sim$ 3 V) intercalation cathode offer a realistic design pathway toward significantly surpassing the energy storage performance of traditional…
Slurry electrodes are an effective means to improve flow battery performance by reducing electrode fouling and increasing the active surface area necessary for electrochemical reactions. It is critical to understand how the slurry…
The responsive behavior of methanethiol and methylthiolate molecules on the Au(111) surface with an applied electrical potential is studied, and it is shown how the sulfur adsorption site, the S-H bond orientation and the interacting energy…
Currently, Sb$_2$Se$_3$ thin films receive considerable research interest as a solar cell absorber material. When completed into a device stack, the major bottleneck for further device improvement is the open circuit voltage, which is the…
Using cryogenic transmission electron microscopy, we revealed three dimensional (3D) structural details of the electrochemically plated lithium (Li) flakes and their solid electrolyte interphase (SEI), including the composite SEI skin-layer…
Silicon (Si) anodes attract a lot of research attention for their potential to enable high energy density lithium-ion batteries (LIBs). Many studies focus on nanostructured Si anodes to counteract deterioration. In this work, we model LIBs…
A safe lithium-sulfur (Li-S) battery employs a composite polymer electrolyte based on a poly(ethylene glycol) dimethyl ether (PEGDME) solid at room temperature. The electrolyte membrane enables a stable and reversible Li-S electrochemical…