Related papers: Stacking fault segregation imaging with analytical…
We report high resolution x-ray diffraction measurements of (Ga,Mn)As and (Ga,Mn)(As,P) epilayers. We observe a structural anisotropy in the form of stacking faults which are present in the (111) and (11-1) planes and absent in the (-111)…
Insight in the structure of nanoparticle assemblies up to a single particle level is key to understand the collective properties of these assemblies, which critically depend on the individual particle positions and orientations. However,…
First-principles alloy theory is used to establish the $\gamma$-surface of Fe-Cr-Ni alloys as function of chemical composition and temperature. The theoretical stacking fault energy (SFE) versus chemistry and temperature trends agree well…
Grain boundary segregations were investigated by Atom Probe Tomography in an Al-Mg alloy, a carbon steel and Armco\trademark Fe processed by severe plastic deformation (SPD). In the non-deformed state, the GBs of the aluminium alloy are Mg…
The intersection between dislocations and a Ag(111) surface has been studied using an interplay of scanning tunneling microscopy (STM) and molecular dynamics (MD). Whereas the STM provides atomically resolved information about the surface…
Atom probe tomography (APT) helps elucidate the link between the nanoscale chemical variations and physical properties, but it has limited structural resolution. Field ion microscopy (FIM), a predecessor technique to APT, is capable of…
Disentangling the relationship between the insulating state with a charge gap and the magnetic order in an antiferromagnetic (AF) Mott insulator remains difficult due to inherent phase separation as the Mott state is perturbed. Measuring…
Stretchable conductors are of crucial relevance for emerging technologies such as wearable electronics, low-invasive bioelectronic implants or soft actuators for robotics. A critical issue for their development regards the understanding of…
Optimising the photoelectrochemical performance of hematite photoanodes for solar water splitting requires better understanding of the relationships between dopant distribution, structural defects and photoelectrochemical properties. Here,…
A systematic study of the compression creep properties of a single-crystalline Co-base superalloy (Co-9Al-7.5W-2Ta) was conducted at 950 {\deg}C, 975 {\deg}C and 1000 {\deg}C to reveal the influence of temperature and the resulting…
There is growing interest in promoting deformation twinning for plasticity in advanced materials, as highly organized twin boundaries are beneficial to better strength-ductility combination in contrast to disordered grain boundaries.…
The electron reflection amplitude $R$ at stacking-fault (SF) induced fractional steps is determined for Ag(111) surface states using a low temperature scanning tunneling microscope. Unexpectedly, $R$ remains as high as $0.6 \sim 0.8$ as…
We study the effect of Stacking Fault Energy (SFE) on the deformation behaviour of copper and copper-aluminium alloys using Molecular Dynamics (MD) simulation. We find that both yield stress and the magnitude of stress drop at yield…
We report results of large-scale molecular-dynamics (MD) simulations of dynamic deformation under biaxial tensile strain of pre-strained single-crystalline nanometer-scale-thick face-centered cubic (fcc) copper films. Our results show that…
The interaction of crystalline defects leads to strain hardening in bulk metals. Metals with high stacking fault energy (SFE), such as aluminum, tend to have low strain hardening rates due to an inability to form stacking faults and…
Segregation to defects, in particular to grain boundaries (GBs), is an unavoidable phenomenon leading to changed material behavior over time. With the increase of available computational power, unbiased quantum-mechanical predictions of…
Stacking fault energy (SFE) is of the most critical microstructure attribute for controlling the deformation mechanism and optimizing mechanical properties of austenitic steels, while there are no accurate and straightforward computational…
Grain boundaries (GBs) trigger structure-specific chemical segregation of solute atoms. According to the three-dimensional (3D) topology of grains, GBs - although defined as planar defects - cannot be free of curvature. This implies…
Atomic force microscopy (AFM) is one of the most promising methods for investigating the structure of materials at the micro and nanoscale levels, as well as their local physical-mechanical properties. The experimental data obtained with…
Using large-scale atomistic simulations, dislocation mechanics in the presence of linear complexions are investigated in an Fe-Ni alloy, where the complexions appear as nanoparticle arrays along edge dislocation lines. When mechanical shear…