Related papers: Plasmoid drift and first wall heat deposition duri…
The recent progress in high-temperature superconductor technologies has led to the design and construction of SPARC, a compact tokamak device expected to reach plasma breakeven with up to $25$MW of external ion cyclotron resonant heating…
In magnetic fusion experiments, a simple technique to evaluate the heat flux on first wall components is a key to controlled plasma surface interaction. The heat flux can be characterized by the peaking factor which is the ratio of the peak…
In the initial stages of ITER operation, ELM mitigation systems need to be commissioned. This requires controlled flat-top operation in type-I ELMy H-mode regimes. Hydrogen or helium plasma discharges are used exclusively in these stages to…
In inboard-limited plasmas, foreseen to be used in future fusion reactors start-up and ramp down phases, the Scrape-Off Layer (SOL) exhibits two regions: the "near" and "far" SOL. The steep radial gradient of the parallel heat flux…
Molecular dynamics simulations have been used to obtain the three-dimensional distribution of interfacial mixing and cascade defects in Ti/Pt multilayer system due to single 1 keV $Ar^+$ impacts at grazing angle of incidence. The Ti/Pt…
The behaviour of a tungsten first wall is studied under the irradiation conditions predicted for the different operation scenarios of the European Laser fusion project HiPER, which is based on direct drive targets and an evacuated dry wall…
The regulation of electron heat transport in high-beta, weakly collisional, magnetized plasma is investigated. A temperature gradient oriented along a mean magnetic field can induce a kinetic heat-flux-driven whistler instability (HWI),…
Recent experimental observations at JET show evidence of reduced ion temperature profile stiffness, hypothesised to be due to concomitant low magnetic shear (s) and significant toroidal rotational flow shear. Non-linear gyrokinetic…
When using Ion Cyclotron Range of Frequency (ICRF) heating, enhanced heat-fluxes are commonly observed on some plasma facing components close to the antennas. Experiments have recently been carried out on JET with the new ITER-Like-Wall…
The impact of electromagnetic stabilization and flow shear stabilization on ITG turbulence is investigated. Analysis of a low-$\beta$ JET L-mode discharge illustrates the relation between ITG stabilization, and proximity to the…
SPIDER is the full-scale prototype of the ion source of the ITER Heating Neutral Beam Injector, where negative ions of Hydrogen or Deuterium are produced by a RF generated plasma and accelerated with a set of grids up to ~100 keV. The Power…
It is planned to use atomic processes to spread out most of the heating power over the first wall and side walls to reduce the heat loads on the plasma facing components in ITER to ~ 50 MW. Calculations indicate that there will be 100 MW in…
In the event of a tokamak disruption in a D-T plasma, fusion-born alpha particles take several milliseconds longer to thermalise than the background. As the damping rates drop drastically following the several orders of magnitudes drop of…
The Heating Neutral Beam Injectors (HNBs) for ITER will have to deliver 16.7 MW beams of H/D particles at 1 MeV energy. The beams will be produced from H-/D- ions, generated by a radiofrequency plasma source coupled to an ion acceleration…
During disruptions in fusion-grade tokamaks like ITER, large electric fields are induced following the thermal quench (TQ) period which can generate a substantial amount of Runaway Electrons (REs) that can carry up to 10 MA current with…
Reliable modeling and control of core density is essential for reactor-relevant magnetic confinement fusion operation, motivating cryogenic pellet injection as a primary fueling actuator and the need for predictive pellet source models in…
Neoclassical and turbulent heavy impurity transport in tokamak core plasmas are determined by main ion temperature, density and toroidal rotation profiles. Thus, in order to understand and prevent experimental behaviour of W accumulation,…
We study radial particle transport in stellarator plasmas using cryogenic pellet injection. By means of perturbative experiments, we estimate the experimental particle flux and compare it with neoclassical simulations. Experimental evidence…
First-principles numerical simulations are used to describe a transport bifurcation in a differentially rotating tokamak plasma. Such a bifurcation is more probable in a region of zero magnetic shear than one of finite magnetic shear…
Sputter thin film deposition after photolithography often produces unwanted spikes along the side edges. These spikes are a significant issue for the development of magnetic tunnel junction (MTJ)-based memory and molecular spintronics…