Related papers: Modeling crack arrest in snow slab avalanches -- t…
Long-term slow-slip events (LSSEs) usually occur on the deep, shallow parts of subducting plates and have substantial relation with adjacent megathrust fault motion. Conventional techniques of quantifying slow earthquake frictional features…
Spatially-explicit estimates of population density, together with appropriate estimates of uncertainty, are required in many management contexts. Density Surface Models (DSMs) are a two-stage approach for estimating spatially-varying…
The modeling of crack propagation in a heterogeneous material using a phase field model is studied numerically in a simple test case: the crack meets a wedge of higher fracture energy. It is shown that when the crack cannot enter the wedge,…
Strain rate sensitivity is a key feature of material deformation, whose importance is growing both because miniaturized components experience higher effective rates and because small scale simulations increasingly probe such conditions. As…
Cracks, the major vehicle for material failure, tend to accelerate to high velocities in brittle materials. In three-dimensions, cracks generically undergo a micro-branching instability at about 40% of their sonic limiting velocity. Recent…
Crack propagation in viscoelastic materials has been understood with the use of Barenblatt cohesive models by many authors since the 1970's. In polymers and metal creep, it is customary to assume that the relaxed modulus is zero, so that we…
Unstable growth of cracks (rough crack surface and crack branching) in dynamic fracture has long been observed in various materials. Until now, there was no universally agreed upon explanation for these instabilities. Here, we demonstrate…
The paper addresses the problem of a Mode III interfacial crack advancing quasi-statically in a heterogeneous composite material, that is a two-phase material containing elastic inclusions, both soft and stiff, and defects, such as…
In the first part of this two-paper series, a new Fragile Points Method (FPM), in both primal and mixed formulations, is presented for analyzing flexoelectric effects in 2D dielectric materials. In the present paper, a number of numerical…
Dissipated energy, representing a monotonically increasing state variable in nonlinear fracture mechanics, can be used as a restraint for tracing the dissipation instead of the elastic unloading path of the structure response. In this work,…
A statistical multi-step self-consistent (SMSSC) micromechanical model for predicting elastic and plastic properties of a three-dimensional Representative Volume Element (RVE) is proposed in this research. A body with randomly distributed…
Combining X-ray tomography with simultaneous shear force measurement, we investigate shear-induced granular avalanches using spherical particles with different surface roughness. We find that systems consisting of particles with large…
We observe the failure process of a fiber bundle model with a variable stress release range, $\gamma$, higher the value of $\gamma$ lower the stress release range. By tuning $\gamma$ from low to high, it is possible to go from the…
We present a gradient-based theoretical framework for predicting hydrogen assisted fracture in elastic-plastic solids. The novelty of the model lies in the combination of: (i) stress-assisted diffusion of solute species, (ii) strain…
The properties of slow crack growth in brittle materials are analyzed both theoretically and experimentally. We propose a model based on a thermally activated rupture process. Considering a 2D spring network submitted to an external load…
We perform large scale simulations of a two dimensional lattice model for amorphous plasticity with random local yield stresses and long-range quadrupolar elastic interactions. We show that as the external stress increases towards the…
Plastic deformation of crystals proceeds through a sequence of intermittent slip avalanches with scale-free (power-law) size distribution. On macroscopic scales, however, plastic flow is known to be smooth and homogeneous. In the present…
In this work, the finite elements method (FEM) is used to analyse the growth of fretting cracks. FEM can be favourably used to extract the stress intensity factors in mixed mode, a typical situation for cracks growing in the vicinity of a…
Velocity jumps observed for crack propagation under a static boundary condition have been used as a controlling factor in developing tough rubbers. However, the static test requires many samples to detect the velocity jump. On the contrary,…
Numerous early warning systems based on rainfall measurements have been designed over the last decades to forecast the onset of rainfall-induced shallow landslides. However, their use over large areas poses challenges due to uncertainties…