Related papers: ANN-based position and speed sensorless estimation…
Non-ideal position estimation results in degraded performance of synchronous motor drive systems due to reduction of the average capability of the drive as well as torque harmonics of different orders. The signature and extent of the…
In this paper, we propose a multi-layer artificial neural network (ANN) that is trained with the Levenberg-Marquardt algorithm for use in signal detection over multiple-input multiple-output orthogonal frequency-division multiplexing…
Force Sensing and Force Control are essential to many industrial applications. Typically, a 6-axis Force/Torque (F/T) sensor is mounted between the robot's wrist and the end-effector in order to measure the forces and torques exerted by the…
Latency in the control loop of adaptive optics (AO) systems can severely limit performance. Under the frozen flow hypothesis linear predictive control techniques can overcome this, however identification and tracking of relevant turbulent…
A deep neural network (DNN) is trained to estimate the speed of a car driving in an urban area using as input a stream of measurements from a low-cost six-axis inertial measurement unit (IMU). Three hours of data was collected by driving…
The diagnosis of induction machines has traditionally relied on model-based methods that require the development of complex dynamic models, making them difficult to implement and computationally expensive. To overcome these limitations,…
Electromagnetic modeling with MAFIA of the combined beam position-phase monitors (BPPMs) for the Spallation Neutron Source (SNS) linac has been performed. Time-domain 3-D simulations are used to compute the signal amplitudes and phases on…
In this paper we investigate the usage of machine learning for interpreting measured sensor values in sensor modules. In particular we analyze the potential of artificial neural networks (ANNs) on low-cost micro-controllers with a few…
Linear Hall sensors are a cost-effective alternative to optical encoders for measuring the rotor positions of actuators, with the main challenge being that they exhibit position-dependent inaccuracies resulting from manufacturing…
Early fault diagnosis is imperative for the proper functioning of rotating machines. It can reduce economic losses in the industry due to unexpected failures. Existing fault analysis methods are either expensive or demand expertise for the…
Modern on-road navigation systems heavily depend on integrating speed measurements with inertial navigation systems (INS) and global navigation satellite systems (GNSS). Telemetry-based applications typically source speed data from the…
In this paper, we describe the algorithm to measure the stroke and the temperature of solenoid using PWM driving current at two points based on the electric characteristics of the solenoid with CNN, without mechanical attachments. We…
Smarty is a fully-reconfigurable on-chip feed-forward artificial neural network (ANN) with ten integrated time-to-digital converters (TDCs) designed in a 16 nm FinFET CMOS technology node. The integration of TDCs together with an ANN aims…
This paper presents fault detection and classification using Wavelet and ANN based methods in a DFIG-based series compensated system. The state-of-the art methods include Wavelet transform, Fourier transform, and Wavelet-neuro fuzzy…
Induction motors are one of the most crucial electrical equipment and are extensively used in industries in a wide range of applications. This paper presents a machine learning model for the fault detection and classification of induction…
Conventional synchronous machines are gradually replaced by converter-based renewable resources. As a result, synchronous inertia, an important time-varying quantity, has substantially more impact on modern power systems stability. The…
This paper presents a novel six-axis force/torque (F/T) sensor based on inductive sensing technology. Unlike conventional strain gauge-based sensors that require direct contact and external amplification, the proposed sensor utilizes…
In order to provide robust, reliable, and accurate position and velocity control of motor drives, friction compensation has emerged as a key difficulty. Non-characterised friction could give rise to large position errors and vibrations…
Several heuristic procedures to estimate the rotor position of permanent magnet synchronous motors (PMSM) via signal injection have been reported in the literature. Using averaging theory, a framework to analyse such schemes has been…
Alternating current (AC) electrical drive control without mechanical sensors is an active research topic. This paper studies the observability of both induction machine and synchronous machine sensorless drives. Observer-based sensorless…