Related papers: Pre-insertion resistors temperature prediction bas…
Failure prediction of any electrical/optical component is crucial for estimating its operating life. Using high temperature operating life (HTOL) tests, it is possible to model the failure mechanisms for integrated circuits. Conventional…
This paper introduces on-chip integrated rotary traveling wave oscillators (RTWOs) organized into rotary oscillator array (ROA) bricks as an external perturbation to induce subharmonic injection locking (SHIL) in oscillator-based Ising…
Visual-inertial odometry (VIO) is widely used for mobile robot localization, but its long-term accuracy degrades without global constraints. Incorporating ranging sensors such as ultra-wideband (UWB) can mitigate drift; however,…
Nuclear power plant operators face significant challenges due to unpredictable deviations between offline and online thermal limits, a phenomenon known as thermal limit bias, which leads to conservative design margins, increased fuel costs,…
Fitting oscillator models to variable-angle spectroscopic ellipsometry (VASE) data can lead to non-unique, unphysical results. We demonstrate using temperature-dependent trends to prevent overfitting and ensure model physicality. As a case…
High voltage insulators are widely deployed in power systems to isolate the live- and dead-part of overhead lines as well as to support the power line conductors mechanically. Permanent, secure and safe operation of power transmission lines…
In this study, in order to reduce the local high temperature of the platform in inertial navigation system (PINS), a pin-fin heat sink with staggered arrangement is designed. To reduce the dimension of the inputs and improve the efficiency…
To guarantee the angular resolution, the Large High Altitude Air Shower Observatory (LHAASO) requires a 500ps (rms) timing synchronization among the 6866 detect units for its KM2A sub-detector array. The White Rabbit technology is applied…
This study proposes a control strategy to ensure the safe operation of modern power systems with high penetration of inverter-based resources (IBRs) within an optimal operation framework. The objective is to obtain operating points that…
This work presents a physics-infused reduced-order modeling (PIROM) framework for efficient and accurate prediction of transient thermal behavior in multi-layered hypersonic thermal protection systems (TPS). The PIROM architecture…
Thermal runaway in lithium-ion batteries is a critical safety concern for the battery industry due to its potential to cause uncontrolled temperature rises and subsequent fires that can engulf the battery pack and its surroundings. Modeling…
The stability ofthe proportional--integral--derivative (PID)controlof temperature in the spark plasma sintering (SPS) process is investigated.ThePID regulationsof this process are tested fordifferent SPS toolingdimensions, physical…
High linear voltage references circuitry are designed and implemented in TSMC 0.18$\mu$m CMOS technology. Previous research has proposed the use of MOS transistors operating in the weak inversion region to replace the bipolar devices in…
In combating climate change, an effective demand-based energy supply operation of the district energy system (DES) for heating or cooling is indispensable. As a consequence, an accurate forecast of heat consumption on the consumer side…
In many situations, the dual-purpose heater/thermometer wires used in the three-omega method, one of the most precise and sensitive techniques for measuring the thermal conductivity of thin films and interfaces, must include bends and…
We apply the finite-temperature variational cluster approach to a strongly correlated and spin-orbit coupled model for four electrons (i.e. two holes) in the $t_{2g}$ subshell. We focus on parameters suitable for antiferromagnetic Mott…
This work focuses on the study of temperature associated with the final heavy fragments in reactions induced by both the neutron-proton symmetric and the neutron-rich projectiles, and with incident energy ranges from 60$A$ MeV to 1$A$ GeV.…
Due to the sensitivity of the piezoelectric layer in surface acoustic wave (SAW) resonators to temperature, a method of achieving device stability as a function of temperature is required. This work presents the design, modeling and…
Accurate knowledge of temperatures in power semiconductor modules is crucial for proper thermal management of such devices. Precise prediction of temperatures allows to operate the system at the physical limit of the device avoiding…
Rail and wheel interaction functionality is pivotal to the railway system safety, requiring accurate measurement systems for optimal safety monitoring operation. This paper introduces an innovative onboard measurement system for monitoring…